hassey

I'll be there Hassey

I'm going to buy por-15 for My brat and my rodeo To me it will worth the price at 33.00 a quart I my get 2 quarts small investment compared to the cost of replacing sheet metal in my opinion I'm using it as a (preventitve not a cure) www.por-15.com Hassey

I might show up could be kinda fun tromping threw the corn fields in my BRAT Hassey

Me <----- native Hassey

call me if you want or leave your number and i'll try to talk you threw it over the phone 303 781 5058 hassey

you will loose no ground clearance it will Not hang any lower than your tow hooks do now it will be flush to the bottom of the bumper just like the trailer hitch is in the photo theres no ground clerance there is there? Hassey

No custom bumper I'm using the same idea as the trailer hitch in the photo and will set under the bumper just like the one in the photo and the ones you see on the street except it will have two ports or sleves 1 on each side of the licence plate with 2 pipes bent in a L shape that will slide in the ports/sleves and you mount your tire carrier on them so it will slide out still remaining in the sleve/ port so you can open the hatch or tail gate don't have any photos cause it still in the making Don't think about the bumper it plays no part in this idea and will stay right where it is you won't even touch it think trailer hitch with two ports/sleves it will mount where the tow hooks are Hassey

I was just talking to the guys at the Colo meet about this yesterday although I have a Brat. It would still work and apply to your hatch. I try to explain if you were to look at the trailer hitch in the photo above or most trailer hitches anymore there square and the hitch will slide out well i'm going to use that idea and put 2 sleves on ether side of the licensce plate and make them about 15" long it will be about 1" 1/2 ID square tubing then then take some round tubig 1" 1/2 OD tubing so that the round tubing will slide in to the squre tubing with a pipe bender bend two pieces of the round tubib in a (L) the bottom part of the (L) should be about 23" long you can cut the end off as needed but a good starting point the (L) round tubing needs to slide in and out of the square tubing easily thats why the 1" 1/2 ID and the 1" 1/2 OD when once you've done that you need to get the tire mount (for me I got mine off of an Isuzu trooper cuz mine are 6 lugs and thats what will work) when mount it to the round tubing so the whole idea is that when you need to open your tail gate or in your case hatch pull the pin and the carrier will slide out and still stay in the square tubing thats why the round tubing needs to be atleast 23" long If i did a lousey job on explaining this maybe someone that does understand can help clean it up a little Hassey

2 hours 43 mins and 25 secs again by my watch And for thoses interrested I will bring 2 rear mud flaps, 2 rear shocks, 2 front bumper pads, 2 front turn signal lights, 2 sfront side marker lights, 1 rear window rubber gasket, 1 complete set of seat belts for the jump seats, all items are from an 84 brat, I have a ton of subaru badgeing too all kinds I have a Pionner Cassette player thatwas in one of my Brats That being said 2 hours 37 mins and 19 secs Hassey

15 hours 40 mins and 38 secs by my watch and counting TI TIC TIC Hassey

I'll be there with the 84 Brat Hassey

Theres an orange 78 wagon at www.pullnsave.com I was just out there todaytheres also an blue 83 hatchback that has all the aluminum/armor/rockerpanels/ that are along the bottom of the doors (what ever the tech name is) all six pieces are there and in good shape, and a couple of legacy wagons, and a 84 white wagon they are open tommrow (Monday labor day) Hassey

I've been there several times only about a mile or two from me but my all time favorite is pull-n-save www.pullnsave.com Ok Dr Krazy It's all on you now. The meeting place(s), and the time(s), i think every ones said sept 18th will work for everyone. so the rest is up to you. I will add one thing if I can and thats that both meeting places be chosen before hand and posted here. example: if we meet at red rocks and convoy to the hamberstand let it be known and posted here first (don't deside the second place standing in the red rocks parking lot) that way if there are a some that can't make the first one they know where to catch up It's just a thought and an Idea thats all not trying to step on toes :cool: Hassey

Meeting at red rocks is great and works for me on the 18th too. just a couple of inputs hamburger stand is Great but theres also a Sonic in Golden 17191 s Golden road about 6 miles from Red Rocks Colfax to 6th to ulysess or for that matter we could just meet and the hambuger stand on Holland too just an input or two. Hassey

I like the looks of line-x compared to rino line, liine -x has cleaner look as far as i'm concered but everyone will have a differant opioinon Line -x Here in denver wants $385.00 for the bed I ask about the rocker panels I want to do thoes and up to the wide molding on the bottom of the door. And for that the want $285.00 I.m assuming that for both sides and not per side Hassey