1 Lucky Texan

have you tried locking/unlocking (actually, setting/disabling the sec. system) with the fob a coupla times?

If the ECU responds to that knock sensor by drastically pulling the timing, it will make the car very sluggish and likely be detrimental to mileage. On some engines, care must be taken to route the cable/connector in the same ways as the original knock sensor. There is a lump in the casting that can lead to cracking a knock sensor if it isn't oriented correctly. maybe it took 500 miles to break?

easy to check the belt's timing, pull the covers, set the marks - find the tooth count for your engine for a triple check. If you reset the ECU (with a scanner or with a battery disconnect) does the car run better at first? check for a stuck caliper, maybe a brake is dragging?

when was the Avalon introduced? yeah, a long time

a Toyota Avalon would be the best car to back away from an eruption. because, backwards, it spells; no lavA HAHAHAHAHAHAHA *cough* HAHAHAHAHAHAHA!!!!!

I'm not sure about a 99 EJ22, but the 'cheapest' kit for that 2.5 interference-engine is the one least likely to fail before the next belt service.

one idea, contact user 'traildogck' over at subaruoutback.org - he even does mobile repairs and casts his own line of bushings!

look for 'chaos' behind the timing covers try jump-start from another vehicle? try turning the crank pulley by hand with a big wrench

does it crank but not start - or no cranking?

oem got shorter in 06/07 - maybe pull from a wreck and swap? or check the usual suspects; cusco, grimmspeed, kartboy, whiteline etc. ?

It's why you constantly read recommendations to change the rollers at the belt service.

belts are tough toothed idler? - not so much.

my guess would be mercury switches probably abandoned in the early 2000s or before, so, right on the cusp lol!

best answer is, doesn't 'seem' to be as common in older cars. but 2009 ? even the 2.5 is not so bad I think as older generations. keep in mind, there are fewer of them in the population so data is tricky to discern. They certainly CAN have HG issues.

I think you can plug the 2 test connectors together under the dash and the relays and fans will cycle.

^^^^ most likely ECU doesn't know the engine is cold, so it doesn't 'choke' it with xtra fuel sent thru the injectors. on your car, there may be 2 sensors. single wire I think is the gauge, 2 wire is for the ECU - maybe near each other on the coolant crossover tube?

learned something new.

if the hatch plunger switch were on the hatch, I'd suggest abraded wiring in the body-hatch boot.... but I think the switch is in the body?

are those Mabuchi motors? just recently read their history on wikipedia.

side note - the belts are TOUGH

i'm just guessing but, don't Subaru and Nissan both use JATCO trans? seems like there is a good chance something would bolt-up. But, I realize also, the trans could easily be built to incompatible specs.... nasioc.com could be a good source for you to check out. Search and read before posting as there's always a coupla folks there ready to attack a noobie it seems.

the only place I've used other than the dealer and myself (well, when I was ill I farmed-out some regular maintenance a coupla times to a generic shop) is AWD Tuning off Justin road in Flower Mound. I'd say they are highly skilled. If you have a conversation with them, do ask about scheduling and time required to complete any work - other than the time they kept it, the work done on my WRX's transmission (ate 2nd gear) was fine - affordable too.

doh - of course. coil very suspicious of course because of waste-spark ignition but, you know that. let us know what you find

yeah, brake upgrades may require a swap to larger rims too for caliper clearance. probably some good info at nasioc.com - just, search and read before asking questions as there's always 1 or 2 snarky types over there.

ido - no oil on the plug boots?