Search the Community
Showing results for tags '1980'.
-
Hi guys. I have a first generation brumby/brat running a EA71 engine that i am looking to replace. I am looking to replace it with an EJ18. Can anyone offer advice on if this is possible or potential problems I may run into. Thanks.
-
New here, hope this post fits guidelines! I recently inherited a 1980 4x4 Brat and I'm at a loss as to what to do with it. I've tinkered in the past but this will be my first ever full project and I'm hoping to get some suggestions/feedback from anyone who has taken on an older Subaru! Some info: EA71 had 80k OG miles and was recently resealed by a friend of mine. Currently runs and drives no problem. Rust isn't too bad, currently grinding out All original glass and body All interior stripped - still have but thinking about spraying bed liner on floor Missing door cards Dash is cracked but not the worst looking Have OG seats but badly need re-upholseting Pics here Willing to put about $5k into it immediately, $10k tops - what's your take?
- 4 replies
-
- bratproject
- rebuild
-
(and 3 more)
Tagged with:
-
Hi Folks!, Any one got a line on where to get new front struts for my 1980DL? All the usual suppliers (RockAuto, Summit Racing, AutoZone, Napa & O'Reilly's) have only rear shocks. Thanks in advance for your help!
- 5 replies
-
- front struts
- struts
-
(and 3 more)
Tagged with:
-
So I pulled my E-A71 to reseal it. Put the engine back in and it starts right up. I take it for a test drive it will only go half throttle then starts to bog down so I let off and stay below that point and it coughs then shuts off and will not start again. I have replaced the spark plugs/wires and coil but it still has no spark i have tested the distributor and pickup. I have tested all the wires in between and everything seems to be as it should but im at a loss as to why it just stopped and everything else seems to be working properly.
- 10 replies
-
- engine wont start
- no start
-
(and 6 more)
Tagged with:
-
I've recently narrowed down my car issues to my carburetor. I have a parts Brat so i took that one out and popped it in mine, all the seals are new but it is a different version. And now gas comes of an odd area so i was going to put the old one back in, but theres a loose lever i can't figure out, can someone tell me where this is suppose to be connected with. its the part where my finger is.
-
- carburetor
- brat
-
(and 2 more)
Tagged with:
-
Parts Needed for 1980 1st Gen BRAT GL I am trying to eliminate a slight shaking at higher speeds and would like to get an alignment done. I found about half of the parts I would like to replace, but I am having trouble finding the inner ball-joint assembly parts. Any help would be greatly appreciated. Thank you! (See the attached photo to match the following numbers) What I REALLY need: 4. Lock nuts 5. Boots 6. Snap rings (boot) 7. Ball-joint assemblys 8. Lock washers What I was able to find and already purchased: 1. Dust seals 2. Snap rings 3. Tie rod ends - Outer ball-joints
- 3 replies
-
- Ball Joint
- BRAT
-
(and 3 more)
Tagged with:
-
Howdy folks, long time lurker here, finally piping up with some questions. I’ve recently acquired a Gen 1 Brat with an EA81 motor and tranny swap. Things are running fine and it’s currently on the road, but I’m looking to drive it from Las Vegas back home to Toronto in a couple of months time when my current gig ends. To do so, I’m trying to compile a list of everything I’m gonna need to replace, acquire, fix and torque down. I’m hoping the USMB can help me out on this front as I try to get everything sorted out. First on the list, I’d like to replace the front axles - the boots on both are completely shot. I’ve read here that a lot of folks prefer having their original axles rebuilt rather than buying replacements. For my purposes, I’ll certainly hold on to my originals for future use, but to drive across the country, I’ll be looking to swap in some new ones. Word on the street is that EMPI have decent build quality, do Gen 1’s and Gen 2’s share the same axle assembly? Rockauto seems to suggest they don’t but it’s not totally clear. Do folks at USMB have a preferred vendor for EMPI? Lastly, if I’m replacing the axles I feel like I might as well do the wheel bearings too - is there anything else that falls in the same category of “might as well replace it” while the wheels and axles are off? I’ve got many more questions as I look to drop a weber on it, delete the EGR, tune up the cooling, switch over to Pertronix from points and possibly upgrade the alternator to a GM, but for now, any guidance regarding my axles and associated upgrades would be tremendously appreciated. Lastly, here’s a pic for those of you that are interested.
-
Hey guys, I need insight. I have a 1980 subaru leone circle headlight model), and i despise the current 1.6L carby, and would really love to make the car a crazy sleeper, with some sort of OLDISH wrx, or wrx STI engine. Can anyone please help me, or has done something like this in the same year model, because i know that the models after the 1980 are very different. please help ASAP
-
- subaruleone
- engine
-
(and 5 more)
Tagged with:
-
Hi; I have a 1984 turbo wagon with an automatic trans. The trans shifts and seems to work like it should, but I have a bad crunching and vibration when the car accelerates. The former owner had new axels installed so not them. I pulled the axels and the splined stubs appear to be loose, maybe something in the front diff? I also have a 1986 turbo sedan for a parts car, dual range 5 speed, that I would like to install into the wagon. Has anyone done a changeover like this? Would the later clutch pedal and cable work on the older car? Just from measuring none of the crossmembers look like they will work, so I guess that I will have to fabracate my own. The rear gears are the same 3:70's, but the sedan has LSD in it. Any ideas, input would really be appreciated.
-
is there a 5 speed transmission you can hook up to an ea71 engine in a 1980 brat? if so what is the easiest way to go about getting it done?