efseiler Posted May 7, 2010 Share Posted May 7, 2010 Hi everyone, I have a 1996 Legacy Outback with a 2.2L engine. The starter is starting to fail (likely due to carbon scoring on the contacts) and I was wondering how difficult it is to remove the starter...I'm going to take it into a shop and have it rebuilt. From the pictures I've seen on the web it looks fairly simple...two bolts mounting it onto the engine and then the electrical cables...is there anything else I should be wary of? Thanks... --Damien Link to comment Share on other sites More sharing options...
NoahDL88 Posted May 7, 2010 Share Posted May 7, 2010 disconnect the batter first But you knew that They are straight forward, 14mm on top 17mm on bottom Link to comment Share on other sites More sharing options...
rtcaravan Posted May 7, 2010 Share Posted May 7, 2010 it's very simple it will take no longer than ten min to pull out. don't forget to unhook the pos. batt cable first. Link to comment Share on other sites More sharing options...
Olnick Posted May 7, 2010 Share Posted May 7, 2010 It really is quite easy, as Noah said. You might want to reach the bottom one from under the car (but it can be done "blind" from the top.) How is it failing? May be as simple as replacing the copper contacts in the solenoid. Try a search for that--it's been talked about in the past. Good luck. Link to comment Share on other sites More sharing options...
efseiler Posted May 7, 2010 Author Share Posted May 7, 2010 well...when I try to turn the engine over it just clicks...usually I have to make 3-4 attempts until the starter finally kicks in and starts the engine. Oftentimes whacking the starter with a wrench will improve its functioning (supposedly it helps the loosen the carbon buildup which I read may be the cause of its poor functioning) Sometimes when the weather is wet enough I can't start it at all and have to wait until it gets drier.... So I can remove the starter from the top without much difficulty? --Damien Link to comment Share on other sites More sharing options...
allwheeldad Posted May 7, 2010 Share Posted May 7, 2010 [quote So I can remove the starter from the top without much difficulty? /QUOTE] It's a Subaru........"difficulty" is a relative term according to how much skin you have on your knuckles! Link to comment Share on other sites More sharing options...
Rooster2 Posted May 7, 2010 Share Posted May 7, 2010 As someone else replied to this thread, there are 2 bolts that affix the starter to the engine block. The bottom long bolt can only be worked on by touch/feel, and can't be seen. Still not a big deal. I jam a rag or paper towel under the nut, so if dropped, it won't fall down deep into the engine bay and be difficult to retrieve. Removing bolts does require a hand wrench to hold the nut, while using a drive to loosen the bolt. For my time and money, I would buy a rebuilt from a parts store, and not waste time waiting to have the old one rebuilt. Rebuilts for me have always lasted a long time, and have a lifetime guarantee. Link to comment Share on other sites More sharing options...
Olnick Posted May 7, 2010 Share Posted May 7, 2010 well...when I try to turn the engine over it just clicks...usually I have to make 3-4 attempts until the starter finally kicks in and starts the engine. Yup, bet it's the copper contacts. They get pitted, burnt and worn over the years. Should be able to get a set online or at an auto-electric shop for 10 or 15 bucks. Link to comment Share on other sites More sharing options...
efseiler Posted May 7, 2010 Author Share Posted May 7, 2010 so there's both a nut and bolt involved? I think I'll just have my mechanic do it....the only things I can do with confidence are fluid changes and replacing the fuel and air filter..... If I had my own shop, lift, tools and equipment it would be like 'going to heaven'... :-) Cheers, Damien Link to comment Share on other sites More sharing options...
mikec03 Posted May 7, 2010 Share Posted May 7, 2010 There is not a nut and bolt involved on the SAME attachment. The only hard part is removing the bottom attachment [nut/bolt-I can't remember] which requires a different socket. I've done two changes on 2.2l engines from the top. On the first one,I tried to use a 14 mm socket on the bottom attachment for 15 minutes before I realized it was a different size LOL! Link to comment Share on other sites More sharing options...
johnceggleston Posted May 7, 2010 Share Posted May 7, 2010 There is not a nut and bolt involved on the SAME attachment. The only hard part is removing the bottom attachment [nut/bolt-I can't remember] which requires a different socket. I've done two changes on 2.2l engines from the top. On the first one,I tried to use a 14 mm socket on the bottom attachment for 15 minutes before I realized it was a different size LOL! the top attachment is a bolt, 14mm socket. the bottom is a nut on a stud, 17mm, which i found so difficult from above that i reached from below. mostly so i could see it. Link to comment Share on other sites More sharing options...
tricked919 Posted May 7, 2010 Share Posted May 7, 2010 I've never seen the inside of a Subaru starter, but I assume they all work the same. I 2nd the "contacts" After all the starts that thing has done, the plunger has probably beaten the copper contacts so bad that it doesn't create a circuit every time you turn the key. New ones are a cheap and easy fix you can probably do on your kitchen table in a few minutes. Link to comment Share on other sites More sharing options...
efseiler Posted May 7, 2010 Author Share Posted May 7, 2010 on my kitchen table? ha ha ha Having neither the time nor the patience I drove it up to my mechanic today... Cheers, Damien Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now