Jump to content
Ultimate Subaru Message Board

81 brat project with pics


Recommended Posts

Hey all, I have had this brat since november and havent been putting too much time into it because of the weather. it started to clear up, so heres some progress.

 

When i first obtained the brat it was sitting in a field, with the drivers side roll up window broken in the down position. This allowed for water and rust to develop, also letting in the elements and creatures. I started to gut it, and found out there was a family of rats living above the blower motor, pissing on everything and eating wires. i had to gut the interior, and patch wires. i have a lot more work body wise, but I am hoping that with the wiring all worked out, that a new battery will get it going.

 

Started by using bedliner to cover a few things

DSCF0063.jpg

 

DSCF0064.jpg

 

DSCF0206.jpg

 

Turned into doing the whole interior

DSCF0207.jpg

 

DSCF0208.jpg

 

Had to solder about 15 wires that the rats chomped through

DSCF0209.jpg

 

bed full o parts n sh*t

DSCF0210.jpg

 

SOME of the rust, i will be repairing with sheet metal

DSCF0211.jpg

 

ea81 in yo face

DSCF0212.jpg

 

more updates with progress. enjoy :grin:

Link to comment
Share on other sites

  • 1 month later...

Update**

Got the beast running and took it around the block!!!!! :lol:

 

Welded a broken hood latch, now it closes

DSCF0221.jpg

 

Put in some 92 saab seats from craigslist

DSCF0222.jpg

 

had to make a bracket for the seats to fit

DSCF0224.jpg

 

tune up and body work next

Link to comment
Share on other sites

Boy, if that is all the rust you have for sitting in a field, I'm envious!

 

I had to clean out one heck of a nest out of my dash from it's time in the field. Makes for a smelling trip to work this past winter.

 

Noticed that your vacuum switches are still attached. Any chance you could take a few pics as to where the line is supposed to go? Mine is not connected and I have yet to figure out where it connected to.

 

On the dash, did toy strip off the original cover and foam?

Link to comment
Share on other sites

DaveAP- I have only the fwd/4wd lever, I wish it had a hi/lo.

 

Torc- I couldn't stand my rat piss heater unit so it all came out. On the dash I just painted over the vinyl/foam like 8 coats. I wish I would have pulled the foam and glassed it. It was just a "what if" it works sort of thing.

How do you want that picture? Like close up of carb throttle body area without air cleaner?

 

 

 

Thanks for the positive feedback!

Link to comment
Share on other sites

  • 3 months later...

UPDATE: started doing body work, i'm a bit further than pictured, but the delay between work and pictures is me just being slow.

 

I started off by patching some rusted out spots with fiberglass and bondo. A lot of the rust formed from a camper shell the guy had on previously

 

DSCF0274.jpg

 

DSCF0275.jpg

 

Heres a before and after of the driver side, the passenger side wasn't as bad, but still horrible nonetheless.

 

BEFORE:

DSCF0211.jpg

AFTER:

DSCF0276.jpg

 

I pulled off the front fenders and bumper cover to repair some rust

DSCF0272.jpg

Front

DSCF0277.jpg

Passenger

DSCF0273.jpg

Driver

DSCF0278.jpg

Passenger front fender

DSCF0279.jpg

zoom

DSCF0280.jpg

Driver side fender and bumper gaurd

DSCF0282.jpg

zoom driver side fender

DSCF0281.jpg

The empty rear tail light holes, im going to have to fab something up,

DSCF0271.jpg

im thinking black diamond plate or sheet metal with two red 4" circular trailer lights, with reverse lights mount to the bumper

Link to comment
Share on other sites

Got a question for you crizzlE, the main fuel line from the firewall to the hard carb lines, where does that connect at the firewall side? I am replacing lines in the next few days and I'm not sure where that line connects or what I will need to do to remove/replace it.

Link to comment
Share on other sites

Got a question for you crizzlE, the main fuel line from the firewall to the hard carb lines, where does that connect at the firewall side? I am replacing lines in the next few days and I'm not sure where that line connects or what I will need to do to remove/replace it.

 

Maddcelt, I took some pics for you, hopefully they will help. let me know if you need more indepth pics.

 

DSCF0295.jpg

 

DSCF0297.jpg

 

DSCF0296.jpg

Link to comment
Share on other sites

UPDATE:

 

As I stated in my earlier post, those pics were a little behind. I did some more work, and now these are the most recent.

 

The Fender with the huge hole, fiber glassed, and bondo-haired

DSCF0291.jpg

 

The fender with the little hole, fiber glassed for now... more work to come

DSCF0292.jpg

 

Cleaned some of the stuff I took pics of earlier, gives you a better view of whats got to be done...

DSCF0298.jpg

Will gc8 impreza struts fit?

DSCF0299.jpg

DSCF0301.jpg

DSCF0302.jpg

 

Latest predicament... vent holes, let water in, when I washed it, what would you use to plug them?

DSCF0300.jpg

 

Good look at jump seats and theoretical tail light configuration (if I cant find some for an 81)

DSCF0304.jpg

theory.jpg

 

Let me know what you think! :banana:

Link to comment
Share on other sites

Maddcelt, I took some pics for you, hopefully they will help. let me know if you need more indepth pics.

 

DSCF0295.jpg

 

 

It surprised me when you said this car was an 81 w/EA81 but NOT a D/R?

 

Well guess what, that is DEFINATELY a D/R trans. You can see the rod running on the drivers side that activates the Hi/Lo. (above picture)

 

Someone must have changed the shifter out.

 

From what I gather, that car is a rarity. Something about a one year only crossmember to fit an EA82 5spd trans? Or something like that

 

C'mon experts, what was so special about the EA81 D/R brat?

Link to comment
Share on other sites

  • 6 months later...

So, I'm back on the brat. Today I did some work, to get the brat ready for rust removal. Took out the radiator, the head lights, and the little splash guards underneath. I found some weird stuff. If you could help, I would be grateful.

 

Heres the ol' girl in her rusty glory.

IMAG0113.jpg

 

What the heck is this little dangly thing right next to the oil sensor? Hopefully nothing. you can see it in a couple of the pics

IMAG0108.jpg

 

Is this what I think it is?! :slobber: opening for a possible turbo?

IMAG0107.jpg

 

What is this? little object on the passengers side of the radiator, looks broken.

IMAG0112.jpg

 

Missing some screws maybe?! Please let me know if I am, because it doesn't look right. :confused:

IMAG0111.jpg

 

Both sides

IMAG0109.jpg

 

The gap between the sub frame and body?! on both sides..... Please don't let this be true.:eek:

IMAG0110.jpg

 

 

Then some gnarly rust......... battery box :eek:

IMAG0114.jpg

 

 

IMAG0115.jpg

 

IMAG0116.jpg

 

IMAG0117.jpg

What its supposed to look like

 

 

I have what looks like a lot of weird problems. some answered questions would be so awesome thanks guys. try not to judge ol shannon too hard :)

Link to comment
Share on other sites

Nice project! Be thankful it could be a lot worse. Your wheel aprons look good. I'll probably be replacing at least one of mine when the time comes.

 

As for your Q's ,

1st pic is a broken wire hold down. That holds the oil sending unit line you have right there next to it.

 

2nd pic , "stove pipe" which would have a paper/foil-esque tube going from that up to the air filter box under the "nose". You can get by w/o it but it helps to have it working in the winter. (carb. warmer)

 

3rd , Broken radiator drain plug. Temp. sensor also in pic - has one wire lead - clean that sucker up with some 0000 steel wool and it'll last another 30 years, :) well , maybe....

 

4th , Crossmember not in ???? Those should be your crossmember bolts holding your wad (engine and tranny) :grin: .... hmmmm , ok , I see it now , you got the engine on the ground ....

 

5th , battery box is like many get even where there's no rust - sort of. Cut and paste. Toughest part for you probably , but again be thankful for that .

 

Have fun! You're doing plenty fine enough for making it functional and enjoyable again. Cheers!

Link to comment
Share on other sites

I'm going through a similar process with my 78 brat I recently purchased. The pics with the missing bolts are for where the front bullbar/pushbar mounts - I just pulled mine off last week for paint prep. Nice work, btw - wish I had the ea81 with d/r

Link to comment
Share on other sites

thanks for all the replies guys! i'm definitely feeling better about this now.

 

 

if these are bolt holes for the push bar, bumper etc. then we are all good because i took those out a year ago and probably forgot. if its not then i'm going to shoot myself. I knew it felt a little floaty when i drove it around the block hahahahha

 

IMAG0111.jpg

 

I knew I could rely on USMB for the answers! :banana:

Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
 Share

×
×
  • Create New...