987687 Posted September 3, 2010 Share Posted September 3, 2010 I'm wondering how to adjust the timing on my car 89GL. It has an ea81 swapped into the stock SPFI. Using the ea82 disty and ea82 flywheel. Since it has the ea82 flywheel it doesn't have the right timing marks. I have no idea how it was set originally since I wasn't the one who swapped it. I has this really funky retaining system too... anyway, I'm not sure the timing is correct and would like to check/adjust so I can get the best mileage/power etc. Thanks for help! Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 3, 2010 Share Posted September 3, 2010 You will have to find TDC of the comp. stroke on the #1 cylinder. Pull the plug and use a drinking straw and flashlight. Once you have that you can mark the flywheel and then make measured hash marks for 5, 10, 15, and 20 DBTDC. Then set it at 20 with a timing light and the green check connectors plugged in. GD Link to comment Share on other sites More sharing options...
987687 Posted September 3, 2010 Author Share Posted September 3, 2010 Awesome! Thanks. Does anyone know the diameter of the ea82 flywheel? Then I can figure out the circumference of the flywheel, and how many mm per degree. Or if someone has the info that would be cool too. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 3, 2010 Share Posted September 3, 2010 Measure the timing marks already on the wheel. They are the same size just in the wrong location. GD Link to comment Share on other sites More sharing options...
987687 Posted September 3, 2010 Author Share Posted September 3, 2010 Measure the timing marks already on the wheel. They are the same size just in the wrong location. GD wicked good point there! Link to comment Share on other sites More sharing options...
987687 Posted September 26, 2010 Author Share Posted September 26, 2010 I've been waiting a few days to ask this ... thanks for getting for forum back up guys!! I pulled the plug on the #1 cyl, turned the engine to it's compression stroke. I made sure it was the comp stroke by pulling the disty cap off, and when the electrode on the rotor pointed to the #1 pole I figured that's the #1 comp stroke. I did the straw thing to find TDC, and TDC comes out to almost exactly 10 DBTDC on the ea82 flywheel. Does that sound correct? Is it supposed to be that close? Or am I doing something wrong? Another question, the disty is turned to far to get the retaining bolt in. Am I correct in thinking that I can just take the disty out, and put it back in twisted. Making sure not to let the rotor/gear turn relative to the disty? In my mind that doesn't mess anything up, just checking to make sure I can do that. Thanks for all the help! I'm still new to playing with distributors and timing. I'm used to the EJ stuff with digital timing. Link to comment Share on other sites More sharing options...
hatchsub Posted September 27, 2010 Share Posted September 27, 2010 I've been waiting a few days to ask this ... thanks for getting for forum back up guys!! Another question, the disty is turned to far to get the retaining bolt in. Am I correct in thinking that I can just take the disty out, and put it back in twisted. Making sure not to let the rotor/gear turn relative to the disty? In my mind that doesn't mess anything up, just checking to make sure I can do that. Thanks for all the help! I'm still new to playing with distributors and timing. I'm used to the EJ stuff with digital timing. Cant help you with the first one but with the distributor issue yes thats correct. If you keep the rotor in the same spot relative to the distributor (so it still lines up where its supposed to with the points on the cap) then you can drop it back in one tooth over one way or the other to get it to bolt down. Link to comment Share on other sites More sharing options...
987687 Posted September 27, 2010 Author Share Posted September 27, 2010 Thanks! I figured it would be fine doing that! Now all I need to do is get input on the flywheel thing, borrow the timing light from a friend and I'll be all set Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 27, 2010 Share Posted September 27, 2010 If that's the case - use 10 as your new zero and set the timing to 20 (30 for you). Should be good to go. GD Link to comment Share on other sites More sharing options...
987687 Posted September 27, 2010 Author Share Posted September 27, 2010 If that's the case - use 10 as your new zero and set the timing to 20 (30 for you). Should be good to go. GD I was hoping you'd chime in I wasn't sure if that was the 10* thing was the norm, or if that's just how mine ended up. I guess I was assuming it would end up in the blank space for some reason... Not on one of the marks. I didn't realize it could end up in different places on the flywheel like that. Anyway, I'm glad all my questions are cleared up!!! I'll add 10 more degrees after 20*, mark it, and get it timed right! Thanks so much to everyone who's given me help with this. You guys are awesome I can't wait to finally hear my little ea81 purr. Great little motor. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 27, 2010 Share Posted September 27, 2010 The difference is in the location of the timing window on the bell-housing. I can't recall how different they are but if your information is correct about where it's pointing at TDC then you should be fine with putting it to 30. GD Link to comment Share on other sites More sharing options...
987687 Posted September 27, 2010 Author Share Posted September 27, 2010 This is probably a really stupid question, but how the heck am I supposed to SEE the timing mark and it spins by? I made a nice visible mark with white chalk. and I can't for the life of me see it as it passes by. What does everyone else use? There's a little orange paint mark at 20* on the flywheel from the previous owner, how did he see that? I don't get it... Link to comment Share on other sites More sharing options...
TheSubaruJunkie Posted September 27, 2010 Share Posted September 27, 2010 This is what you need a timing light for. It flashes right as the mark passes by, and allows you to see it. Link to comment Share on other sites More sharing options...
987687 Posted September 27, 2010 Author Share Posted September 27, 2010 ah ha... I guess I can borrow one tomorrow from my friend. I was just gonna pull the plug wire so I could see it spark as the mark went by... I tried shining a flashlight at it, but didn't work. I guess once I get the light it'll all make sense... thanks Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now