Cup O Noodles Posted October 23, 2010 Share Posted October 23, 2010 I talked to my local used Subaru dealer about constructing a Frankenmotor and he seemed pretty sure that 2.2 heads wouldn't fit on a 2.5 block. Of course, I've done a bit of research on this site so unless we have a bunch of story tellers here, I suspect they fit just fine. The reason he gave for not believing they were compatible was that the 2.5 was DOHC, some of them at least. I didn't want to argue with the guy because I really don't know crap but I really didn't think the cams would have anything to do with the head fitting to the crankcase. Am I right on this one? Is there any reason any of the 2.2 engines wouldn't be compatible with any of the 2.5 engines? In fact...is the difference between the 2.2 types outside the block? Ugh, it is, isn't it? It won't matter at all what 2.5 short block I get, they'll all be exactly the same. I think I just answered my own questions didn't I? -Thanks. Link to comment Share on other sites More sharing options...
LeoneTurbo Posted October 23, 2010 Share Posted October 23, 2010 Any EJ head bolts up to any EJ block. But make sure that when using a closed deck block, the coolant patterns of block, gasket and head match. Also check if the head combustion chamber matches the cylinder bore of the block you intend to use if you plan to run a head of a bigger engine on a smaller block, extreme example EJ25 block and EJ18 head. Always use the head gasket that matches the block (due to cylinder bore). Link to comment Share on other sites More sharing options...
GeneralDisorder Posted October 23, 2010 Share Posted October 23, 2010 Not all EJ25 blocks are the same - but the frankenmotor generally consists of the EJ25D block with EJ22E heads (from any year you desire). The reason the 25D is used is because the pistons are taller and provide higher compression than the EJ251 and up. That and the EJ25D is the cheapest of the 2.5 blocks. Your local dealer doesn't know much about Subaru engine's apparently. But that's not uncommon - they don't do many engine tear downs and they surely haven't ever tried to fit a part from a 2.2 to a 2.5 - there would be no reason for them to do this. The DOHC head design goes all the way back to the first EJ20's built in the late 80's. The DOHC/SOHC has nothing to do with the head fitting to the block - only the way the cams fit to the heads. All EJ 4 cylinders have the same head/block mating with only minor changes in cooling ports, etc. GD Link to comment Share on other sites More sharing options...
idosubaru Posted October 24, 2010 Share Posted October 24, 2010 yeah dealers are not in the business of swapping/interchanging parts. they're the worst source for info of that type, i would never think to even ask them even though some are very competent. if one happened to be familiar with stuff like this, that would be the exception, not the rule. Link to comment Share on other sites More sharing options...
Cup O Noodles Posted October 24, 2010 Author Share Posted October 24, 2010 Good, I'm glad he's probably not an idiot. He seems like he knows what he's talking about otherwise. Thanks for the info. Link to comment Share on other sites More sharing options...
renob123 Posted October 25, 2010 Share Posted October 25, 2010 Any EJ head bolts up to any EJ block. But make sure that when using a closed deck block, the coolant patterns of block, gasket and head match. Also check if the head combustion chamber matches the cylinder bore of the block you intend to use if you plan to run a head of a bigger engine on a smaller block, extreme example EJ25 block and EJ18 head. Always use the head gasket that matches the block (due to cylinder bore). I don't think the OP has any closed-deck EJ25s in his country. Thanks for making all of us drool, though:) Jacob Link to comment Share on other sites More sharing options...
LeoneTurbo Posted October 26, 2010 Share Posted October 26, 2010 I doubt anybody has a (factory) closed deck 2.5L, I was referring to the USDM Legacy 2.2 Turbo block I've got quite a lot of experience building hybrid Subaru engines, mainly turbo though. I've tried all sorts of combinations and generally 2.5L heads do not work on smaller bore blocks as the diameter of the combustion chamber in the head is bigger than the diameter of the cylinder bore. Link to comment Share on other sites More sharing options...
LeoneTurbo Posted October 26, 2010 Share Posted October 26, 2010 My next Frankenmotor I'm going to build is a hybrid build using JDM EJ15 cylinder heads and block (cylinder bore 85 mm) with a Phase I EJ25D crank (stroke 79 mm), displacement 1.795cc. It will be breathed on by either a small TF035 turbo (used on EUDM Forester 2L Turbo) or a TD04-13G. Custom made pistons and Pauter small big end rods. This should make for a nice torquey motor. I will be running it on a JDM Version IV STI ECU, which on a 2L makes 255 lb-ft and 280 HP. On my hybrid motor I hope to get 200 lb-ft and 210 HP at 5500 rpm. Link to comment Share on other sites More sharing options...
Gloyale Posted October 26, 2010 Share Posted October 26, 2010 I doubt anybody has a (factory) closed deck 2.5L, IIRC, EJ257 is Semi closed (bridges at top, bottom and sides) Link to comment Share on other sites More sharing options...
renob123 Posted October 26, 2010 Share Posted October 26, 2010 IIRC, EJ257 is Semi closed (bridges at top, bottom and sides) Yeah, that's the closest to a closed 2.5 that I know of. LeoneTurbo's advice still holds regarding making sure the coolant passages line up. I think I remember the EJ257 coolant passages being pretty different than previous blocks. Jacob Link to comment Share on other sites More sharing options...
WoodsWagon Posted November 3, 2010 Share Posted November 3, 2010 http://forums.nasioc.com/forums/showthread.php?t=1107352 Has some good pics of the drilled headgasket. Link to comment Share on other sites More sharing options...
LeoneTurbo Posted November 3, 2010 Share Posted November 3, 2010 Yeah, that's the closest to a closed 2.5 that I know of. LeoneTurbo's advice still holds regarding making sure the coolant passages line up. I think I remember the EJ257 coolant passages being pretty different than previous blocks. Jacob That's not just the EJ257, but all post-1999 engines (SOHC and DOHC share same gaskets/pattern) and all pre-1999 DOHC engines. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted November 3, 2010 Share Posted November 3, 2010 Huh - we didn't do a thing to the head gaskets with the EJ25D and EJ22E heads. They looked close enough and it's running just fine on an EA81 radiator with 1-1/4" inlet/outlet . GD Link to comment Share on other sites More sharing options...
renob123 Posted November 3, 2010 Share Posted November 3, 2010 I did a pretty fierce amount of research and asked some of the gurus on NABISCO before doing this. The general consensus is that you can do it either way you want. I opted to not drill partly because I didn't want to compromise the integrity of the gasket, and mostly because I didn't want to eff anything up. I only know of one Frankenmotor failure, and I remember when that guy was experimenting with turbos and superchargers on that same block. This was back before the kind of advanced engine management we have nowadays. Jacob Link to comment Share on other sites More sharing options...
GeneralDisorder Posted November 4, 2010 Share Posted November 4, 2010 This was back before the kind of advanced engine management other people besides myself have nowadays. Jacob Fixed . GD Link to comment Share on other sites More sharing options...
renob123 Posted November 4, 2010 Share Posted November 4, 2010 Fixed . GD I don't get it... https://docs.google.com/viewer?a=v&pid=sites&srcid=ZGVmYXVsdGRvbWFpbnxhc3ViaWVuZXdiaWV0dW5pbmdndWlkZXxneDoxMGYzM2M5NjBlYzY3ODI4 Jacob Link to comment Share on other sites More sharing options...
nemorzuz Posted November 26, 2011 Share Posted November 26, 2011 Inspiring! I will buy a Legacy 2.2 GX again, I miss it too much. And then it will be franken motored! I love the minimalistic way of building! Most power for least money. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now