Mendodave Posted March 1, 2004 Share Posted March 1, 2004 Hi all... I went by the PnP in Windsor yesterday, looking for a better Hitachi than I have, my throttle shaft is worn out. the only '80-84 car there was a Nice Hatchback, 4wd, perfect maroon body, no bumpers. Unfortunately it had a bad engine fire then there was what looked like an XT6, but the back of the car said it was a GL. SPFI and manifold ready to go, the heads are gone off the car. there were also two Peugots with the 15 inch mag wheels like these on my car...great shape. (missing two lug nuts;-)) can't afford a redline weber kit right now, but maybe i should just go for it. Dave Link to comment Share on other sites More sharing options...
MilesFox Posted March 1, 2004 Share Posted March 1, 2004 try an ea82 hitachi carb on your existing manifold. the only difference is the air cover for the carb itself, the black ones go to ea82 carbs, bigger hole. but ea82 carb will bolt up to ea81 hitachi intakes Link to comment Share on other sites More sharing options...
Mendodave Posted March 1, 2004 Author Share Posted March 1, 2004 Hi Miles, thanks! there were a few 85-88 EA82 series, one had a decent looking carb. So I would need that AND the airfilter housing? I don't need to get smogged again, so the different aircleaners are fine... david Link to comment Share on other sites More sharing options...
TheSubaruJunkie Posted March 1, 2004 Share Posted March 1, 2004 Dave... are you planning any more trips to the Rancho area? Last time I was at the yard here, they were down to 1 row of subaru's, but they had a few EA81's left. I need to make a trip there myself to get another hitachi for my wagon, maybe if you can find the time we can make a yard run. -Brian Link to comment Share on other sites More sharing options...
MilesFox Posted March 1, 2004 Share Posted March 1, 2004 yeah, if you mount an ea82 carb, you will need the LOWER air filter housing. the housing all hooks up the same, in all the same places, its just the hole for the carb is bigger. the lids and the filter themselves are the same between the 2 Link to comment Share on other sites More sharing options...
Skip Posted March 1, 2004 Share Posted March 1, 2004 Dave, I don't know if your car has an 02 sensor and therefore an ECU. But when shopping for a carb you may want to watch for the feedback type Hitachi's. The mix and match of using one on a car not equiped with the duty solenoids could prove frustrating. I do believe they were prevalent in CA Link to comment Share on other sites More sharing options...
Mendodave Posted March 1, 2004 Author Share Posted March 1, 2004 Hi Skip, I have a CA car with no O2 sensor, so I guess I don't need that? it is a 1984 model Brian: what are your days off? d Link to comment Share on other sites More sharing options...
TheSubaruJunkie Posted March 1, 2004 Share Posted March 1, 2004 I have tomorrow (tuesday) and Friday off. Open both days, except for tomorrow i gotta bowl at 6pm. -Brian Link to comment Share on other sites More sharing options...
Tom63050 Posted March 2, 2004 Share Posted March 2, 2004 Dave, I have a carb from my 84 which ran fine when I took it out to swap in a Weber. Yours for postage. I used to live in Cannon Beach, OR. I sold you a buncha stuff out of an 82 I was parting out, including the motor. Met you halfway between CB and Mendocino by some town's post office, then we had lunch. About three/four years ago I guess. Tom Link to comment Share on other sites More sharing options...
Mendodave Posted March 2, 2004 Author Share Posted March 2, 2004 Heck yes I remember you! That is the trans I am going to put in the '84. The one I drove up to meet you in got buried in the sand on the beach here, high tide took care of all the rest....like the carb I got from you, my digital camera, tools, VOM, etc. I did get the dog out! my present carb has a badly worn throttle shaft, can you check that one and see if it wiggles? if not, i will take it! David Russell 41500 Airport Road Little River, CA 95456 Link to comment Share on other sites More sharing options...
GeneralDisorder Posted March 2, 2004 Share Posted March 2, 2004 Incidentally - ALL the hitachi's I have looked at have worn throttle shafts, but it doesn't seem to affect them much. The one I just rebuilt and installed on my Brat wiggles quite a bit, and came from a car with 189k on it. Runs PERFECTLY. Also - if that really is your problem, then might I sugest giving CCR a call. They sell "throttle bases" with new shafts for $40 plus a core. All you would have to do is bolt on your existing carb to the throttle base, and send the old one back to them. The throttle base itself is iron, and the shaft is Brass, so just a new shaft is all you really need...... I still think this isn't your problem tho. What are your symptoms? GD Link to comment Share on other sites More sharing options...
Tom63050 Posted March 2, 2004 Share Posted March 2, 2004 Dave, will check wiggle factor and get back to you tomorrow. Tom Link to comment Share on other sites More sharing options...
Mendodave Posted March 2, 2004 Author Share Posted March 2, 2004 Sounds like a dance step... Symptoms: set idle, fine for a few days, then idles too high or low. reset idle, ditto burble in exhaust, usually there is the nice steady purr, but with a burble in it occaisonally. I've been told that is a vacuum leak. the car does run pretty damn well, got over 300 miles on the last tank, filled it before the light came on, 10 gallons. not bad for a lifted wagon the carb got worse 'cause i cleaned it, and all the dirt that was clogging the leak came out. d Link to comment Share on other sites More sharing options...
Tom63050 Posted March 4, 2004 Share Posted March 4, 2004 Dave, jiggled a coupleof thingys on the carb and it seems fine. And anyway it ran fine when I took it off. Lemme know if you want me to send it. Tom Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now