idosubaru Posted June 21, 2011 Share Posted June 21, 2011 where do you get sheet metal for rust repair? like just flat sheets for welding/riveting into place? Link to comment Share on other sites More sharing options...
bheinen74 Posted June 21, 2011 Share Posted June 21, 2011 best to get off of old washing machines/refrigerators/furnaces, it is a better grade and is coated well on one side already. Link to comment Share on other sites More sharing options...
desertsubaru Posted June 21, 2011 Share Posted June 21, 2011 I have a 5'x4' piece of roof metal that I cut out of parts wagon. PM me maybe we can make a trade. I would even meet you at the halfway point to Morgan town from Gassaway. That would be the town of Weston WV. Link to comment Share on other sites More sharing options...
MilesFox Posted June 22, 2011 Share Posted June 22, 2011 I second old appliances. I used part of a furnace cover, some thinner metal from home depot(not cost effective in large quantities) and part of an xt fender. The xt fender welded the best, being thicker. The xt metal was soft and pliable, versus the metal from home depot was stiffer and thinner. The furnace cover was more like the metal on the car, softer and more bendy. for rivet patching, i have used ductwork, roofing flash, and u-haul truck roof skins aluminum(the best!) Link to comment Share on other sites More sharing options...
idosubaru Posted June 22, 2011 Author Share Posted June 22, 2011 for rivet patching, i have used ductwork, roofing flash, and u-haul truck roof skins aluminum(the best!)i've seen some of your posts and pictures miles - how do you do the rivet work/patching? i doubt i'll weld, i can't imagine getting it to look right/set flush and grinding down the weld...seems like a mess. time is key here, i don't want this to take all day. i'm just doing small areas in low visibility areas (bottom of car) - like 5x5" and most if it will be covered up by mudflaps so i'm not that worried about cosmetics. get the rust out, water proof it and paint it something close to match. not a show car. Link to comment Share on other sites More sharing options...
Turbone Posted June 22, 2011 Share Posted June 22, 2011 I made a airbox for my CAI out of a computer case. Very stout metal and its a good size to work with. Link to comment Share on other sites More sharing options...
bheinen74 Posted June 22, 2011 Share Posted June 22, 2011 to do it with riveting. place the patch metal behind the original cars metal drill holes thru both, pop rivet in place. Then you need to get the rivets recessed, so give them a whack down with a ballpeen hammer to smash the metal down some to allow for a topcoat of filler, bondo etc. - i do recommend a sealer between the seams to prevent moisture from occurring over time. Link to comment Share on other sites More sharing options...
idosubaru Posted June 22, 2011 Author Share Posted June 22, 2011 awesome, thanks rob i have some old computers too. some flourescent light fixtures were replaced too and i can probably pilfer some of those for metal too. got a wrecked fender/hood that might work if there's enough good metal left. Link to comment Share on other sites More sharing options...
Ricearu Posted June 23, 2011 Share Posted June 23, 2011 I made a airbox for my CAI out of a computer case.Very stout metal and its a good size to work with. ha i never thought about that. that's gettin done this weekend. and the wife wanted me to toss those old cases... HA! Link to comment Share on other sites More sharing options...
backwoodsboy Posted June 23, 2011 Share Posted June 23, 2011 best to get off of old washing machines/refrigerators/furnaces, it is a better grade and is coated well on one side already. +1 ... another vote here for appliance metal! Most of the time its free on the curb. Link to comment Share on other sites More sharing options...
davebugs Posted June 23, 2011 Share Posted June 23, 2011 Back in the day a local shop used to cut new sunfoors into cars and trucks. I'd grab metal there - but that isn't done as much anymore. I've been known to ask local body shops to keep damaged hoods and fenders to be metal donors. I have some stuff here to play with my MIG welder when I get a chance that came from the VW dealer bodyshop. Duct work (galvanized) I believe makes toxic fumes if welded. I'm also not so sure how well putty and stuff sticks to it even if roughed up pretty good. Just remember to use 1/8" rivets when possible to aid in hideing them later. Link to comment Share on other sites More sharing options...
idosubaru Posted June 23, 2011 Author Share Posted June 23, 2011 i have a wrecked fender and hood - not sure if the hood metal is useable or not, it's like two ply i imagine. i'll figure something out, you guys have given me enough options no doubt. looks like the neighbor has some trucks being parted out/repaired too. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now