jarl Posted July 30, 2011 Share Posted July 30, 2011 I'm sorry if this is a stupid question, but: I need new nuts for the exhaust manifold studs, and I would really like to use something that won't corrode and get stuck to the manifold that easily. Stainless seems to be the way to go, but I have not been able to find M10x1.25 flanged nuts in SS -as a matter of fact I have not found any SS nut with that pitch-. Also, SS nuts doesn't seem to be used for load-bearing purposes, as what I have found so far (M10x1.5) has very low specs. I know they exist because the EJ25 I'm replacing had them (before you ask: the studs, not the nuts, were somewhat corroded, and it would be a tall order to remove the nuts -one had to be cut already- AND... I don't know which grade were those) but where can I buy them from? Link to comment Share on other sites More sharing options...
nipper Posted July 30, 2011 Share Posted July 30, 2011 Try a real speed shop. McMaster carr has them too but i think you have to get them by the box. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted July 30, 2011 Share Posted July 30, 2011 They are 10 x 1.25..... you will not find them under most metric listings. They are known as "JIS serrated flange nuts".... JIS stands for Japanese Industrial Standard - which calls for 6 x 1.0, 8 x 1.25, and 10 x 1.25. I buy mine from here: http://www.nutsandbolts.com/nuts-metric-flange-nuts-jis-c-35_195.html GD Link to comment Share on other sites More sharing options...
Fairtax4me Posted July 30, 2011 Share Posted July 30, 2011 Very hard to find Metric Stainless hardware at your typical hardware stores. A specialty hardware/fastener shop such as Fastenal might have them. I usually just use a nut and washer when I replace that sort of thing. Link to comment Share on other sites More sharing options...
jarl Posted July 30, 2011 Author Share Posted July 30, 2011 Hello GD, Nipper I saw flanged zinc nuts somewhere (I've checked so many places I don't remember where), but with the mess I found on the ej22 I'm somewhat reluctant to use anything but stainless. How are those zinc nuts holding up so far? Btw: I bought the studs from 1stsubaruparts, but the finish is quite different from the ones I removed from the other two engines. Does anybody know what finish are they supposed to be? I would assume phosphate, but these look so cheap... Link to comment Share on other sites More sharing options...
GeneralDisorder Posted July 30, 2011 Share Posted July 30, 2011 Stainless is not really going to help - it will gall something fierce. You are better off going with zinc and treating them with copper anti-seize. The stock studs and nuts are zinc coated. I buy the studs from Subaru but their prices on the nuts are outragous - I buy 50 nuts at a time in both 8mm and 10mm from the link I posted above and the quality is very good. GD Link to comment Share on other sites More sharing options...
Quidam Posted July 31, 2011 Share Posted July 31, 2011 I need new nuts for the exhaust manifold studs, and I would really like to use something that won't corrode and get stuck to the manifold that easily. I know they exist because the EJ25 I'm replacing had them (before you ask: the studs, not the nuts, were somewhat corroded AND... I don't know which grade were those) but where can I buy them from? Subaru. You're in Detroit so you are seeing what I see. Subaru exhaust nuts are 304 stainless. If you can salvage any, make sure to run a tap through them and not just try to rethread using a bolt. Doug Link to comment Share on other sites More sharing options...
CNY_Dave Posted August 1, 2011 Share Posted August 1, 2011 Use Brass nuts for the win! Dave Link to comment Share on other sites More sharing options...
GeneralDisorder Posted August 1, 2011 Share Posted August 1, 2011 Yeah - copper or brass will work. You see that a lot on German cars. Stainless bolts/studs with copper nuts. Neither will corrode but if you make them both stainless you will never get them apart - galling sucks. GD Link to comment Share on other sites More sharing options...
jarl Posted August 2, 2011 Author Share Posted August 2, 2011 (edited) Great! Now... where do I find those brass/copper nuts Which other cars use the M10x1.25 studs? Quidam: thank you for confirming the Subaru nuts are SS. The only issue right now is that the local dealer is really, *really* poor. BTW: the studs I got from 1stSubaruParts are not SS... which makes sense considering they are bolted directly into aluminum. They look like cheap zinc studs, though I'd like to think they have some fancy protection (phosphate+zinc, hopefuly?)... Edited August 2, 2011 by jarl Stud material Link to comment Share on other sites More sharing options...
Quidam Posted August 9, 2011 Share Posted August 9, 2011 Great! Now... where do I find those brass/copper nuts Which other cars use the M10x1.25 studs? Quidam: thank you for confirming the Subaru nuts are SS. The only issue right now is that the local dealer is really, *really* poor. BTW: the studs I got from 1stSubaruParts are not SS... which makes sense considering they are bolted directly into aluminum. They look like cheap zinc studs, though I'd like to think they have some fancy protection (phosphate+zinc, hopefuly?)... Well, it's been nuts here:) You can get the brass nuts from the UK. Honda, Toyota uses the same size studs and nuts and Japanese sport bikes use the same size for sprocket nuts. Available in Ti, stainless, aluminum with stainless insert. Lug nuts for a four wheeler look like they might work and are cap nuts, enclosing all the threads. I ordered a dozen stainless sprocket nuts from the UK for about $1.25 each shipped. I've been buying this stuff from the UK and China lately. Yea, and the idea with stainless is to use a soft metal on the stud/nut combo for anti seize. Tho I did buy a dozen zinc studs, nuts, and washers to have on hand. $10.00 at a local muffler shop. Doug Link to comment Share on other sites More sharing options...
jarl Posted August 10, 2011 Author Share Posted August 10, 2011 Trust me... it has been nuts around here too Somehow I don't feel like ordering those nuts from overseas... or at least not yet In particular because I need to finish this car NOW Yesterday I went junkyard hunting, looking for an ignition coil for the EJ22. While there I decided to try and get more SS nuts out of a couple of subies I found, and got home with four nuts and four nuts+studs. A liberal amount of a propane torch on these provided four more nuts for my collection. However, of the eight, maybe 2 were smooth The other looked like they had shrunk I don't have a tap and further attempts to clean the thread faileds, so I decided to leave the nuts in a jar with evaporust... and voila! Now I have exactly 6 working SS nuts, ready to be used. It looks like some metal from the studs embeds itself into the nuts, and the evaporust is just strong enough to remove it. Link to comment Share on other sites More sharing options...
Quidam Posted August 11, 2011 Share Posted August 11, 2011 I might have to try that stuff. I have at least a dozen of those nuts still on the stud. You know, where the threads are corroded away. Subaru put those stainless nuts so at least we'd still have a nut intact to extract the stud, I guess. Doug Link to comment Share on other sites More sharing options...
jarl Posted August 11, 2011 Author Share Posted August 11, 2011 Just to be clear: evaporust will help you cleaning the nuts after you remove them. It may actually ease the nut removal a bit, but the torch and a breaker bar (and good vise grips) are the main ingredients Link to comment Share on other sites More sharing options...
Quidam Posted August 11, 2011 Share Posted August 11, 2011 I've taken the power hacksaw and cut the threads off above the nut, so that should help too. Yea, heat and the vice for this job. I've got access to aceteline now:) Doug Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now