hankosolder2 Posted August 23, 2011 Share Posted August 23, 2011 I just bought a '98 Legacy Wagon. 214K. One of the rear struts has failed to the extent that the strut cartridge insert and rod has pulled out from the main tube of the strut assembly. So, there's nothing to limit the travel of the spring if the weight of the car is not on the strut assembly and it's unbolted from the car. I need to replace the strut (duh) and if I try to unbolt this thing as an assembly, I think the spring might go flying. I guess I could see if I can get a spring compressor on it while the hub is resting on a jack... has anyone run into this problem, and if so, how did you work around it? Nathan Link to comment Share on other sites More sharing options...
Hocrest Posted August 23, 2011 Share Posted August 23, 2011 If I understand correctly, the upper rod has pulled out of the lower cartridge? If so, don't worry about compressing it, just jack up the car and it will reach it's max extension without flying out. Link to comment Share on other sites More sharing options...
Fairtax4me Posted August 23, 2011 Share Posted August 23, 2011 Yeah I wouldn't worry about it too much. The springs are only about an inch longer when uncompressed. That much won't make any difference to the suspension. Link to comment Share on other sites More sharing options...
hankosolder2 Posted August 23, 2011 Author Share Posted August 23, 2011 Thanks guys- good to know. I'm really (overly?) cautious with compressed springs. Knowing that it'll decompress enough w/o flying off and impaling something or someone is a big help. Nathan Link to comment Share on other sites More sharing options...
zundfolge Posted August 23, 2011 Share Posted August 23, 2011 Perhaps this is stating the obvious, but if you are going to replace the strut but keep the old spring it you are going to need to procure a spring compressor anyway. Link to comment Share on other sites More sharing options...
Rooster2 Posted August 23, 2011 Share Posted August 23, 2011 For what it is worth, in replacing a shock or strut, I put a bottle jack on the very bottom of the shock/strut, then jack it up to the proper height, so I can easily bolt the top in place. This technique has worked great for me in the past. I use pieces of 2X4 or whatever, placed under the bottle jack to get the desired height before jacking. Link to comment Share on other sites More sharing options...
hankosolder2 Posted August 28, 2011 Author Share Posted August 28, 2011 I installed the new struts today. The "broken" side (longer than a normal strut assembly where the spring extension is limited by the strut rod) took a bit of maneuvering to get past the lower suspension arms, but came out OK. I was planning on taking pictures of the bad strut, but I left them out back and the metal scrapmen took them before I had the chance to get my camera! Thanks for the advice! Nathan Link to comment Share on other sites More sharing options...
Rooster2 Posted August 28, 2011 Share Posted August 28, 2011 What brand and model strut did you install? Was the spring bad as well? Link to comment Share on other sites More sharing options...
hankosolder2 Posted August 28, 2011 Author Share Posted August 28, 2011 I installed KYBs. The old spring was just fine. I think the strut which failed was OEM...'98 with 200+K miles on it- the tube was incredibly badly rusted- never seen anything like it before, even on older cars than this. Link to comment Share on other sites More sharing options...
Rooster2 Posted August 30, 2011 Share Posted August 30, 2011 I installed KYBs. The old spring was just fine. I think the strut which failed was OEM...'98 with 200+K miles on it- the tube was incredibly badly rusted- never seen anything like it before, even on older cars than this. Enjoy the KYBs. A great strut at a reasonable price. KYBs are what I always install. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now