Fozester Posted February 29, 2012 Share Posted February 29, 2012 I went on some telephone line service trails with a buddy of mine. Then we headed up the hills of the gorge to get some snow. And we found plenty of it. Thank god I bought a 3/16" skid plate from Primitive. My buddy was not so lucky and lost his brand new franken motor. Link to comment Share on other sites More sharing options...
91leglift Posted February 29, 2012 Share Posted February 29, 2012 ya i dont know if it was me hitting something that knocked the plug lose or the fact i didnt have a new crush washer but either way ive learned my lesson. New oem crush washer every time and check the plug after i go wheeling till i get a skid plate made. But on a good note i got a new engine last night and im going to tear it apart tonight and get it off to the machine shop tomorrow Link to comment Share on other sites More sharing options...
Fozester Posted February 29, 2012 Author Share Posted February 29, 2012 Well if you are looking for some extra cash in a week from now, I should be ordering my hellas and will need that light tab welded on. Are you gonna put the dual-range in while you have the motor out? Link to comment Share on other sites More sharing options...
scoobyclimbs Posted February 29, 2012 Share Posted February 29, 2012 looks like post canyon in hood river? We head a great time in the coast range snow and then sand lake.. Link to comment Share on other sites More sharing options...
Fozester Posted February 29, 2012 Author Share Posted February 29, 2012 Well after he puts in the new motor we hope to do it again. You are welcome to tag along. Link to comment Share on other sites More sharing options...
91leglift Posted February 29, 2012 Share Posted February 29, 2012 ya im going to try sometime next week if i can get the motor back in time to get the D/R atleast test fitted so i can mount it when i have the extra cash to extend my driveline. ill be pushing it to try and get the car ready with atleast outback struts for the browns camp trip and i need really big wheel spacers cause my new tires hit the strut Link to comment Share on other sites More sharing options...
Red92 Posted February 29, 2012 Share Posted February 29, 2012 Bummer on the engine. :-\ Was it just oil loss that did it, or physical impact damage? Did you have to tow it out? Link to comment Share on other sites More sharing options...
scoobyclimbs Posted February 29, 2012 Share Posted February 29, 2012 ya i dont know if it was me hitting something that knocked the plug lose or the fact i didnt have a new crush washer but either way ive learned my lesson. New oem crush washer every time and check the plug after i go wheeling till i get a skid plate made.But on a good note i got a new engine last night and im going to tear it apart tonight and get it off to the machine shop tomorrow Why a new crush washer ? I've reused about a thousand crush washers on about every make and model of car/truck heavy equipment..etc. since the mid 80's...never had a problem... If you hit it that's another issue.. I haven't lost a motor yet . Unless it's damaged reuse it. Link to comment Share on other sites More sharing options...
scoobyclimbs Posted February 29, 2012 Share Posted February 29, 2012 Next time you head out that way let me know ..I've been going out there since 1990...I know about every trail out there... Mt.Defiance has some of the best..Middle mtn. , Surveyors ridge...etc.. Link to comment Share on other sites More sharing options...
91leglift Posted February 29, 2012 Share Posted February 29, 2012 i must have hit it lose on something and it vibrated out when i was driving in town later that night. it melted bearings to the crank and rods and snapped a rod in half which took a chunk of cylinder with it Link to comment Share on other sites More sharing options...
GeneralDisorder Posted February 29, 2012 Share Posted February 29, 2012 You have to make sure it *has* a correct crush washer though. I've seen lots of cheap one's that were squished out and one's that leak, etc. Or just plain missing. I typically replace them with OEM one's when I change the filter. I don't always replace one's that I know I've replaced in the past and that still look good but I do swap them out. It's worth it to me to not have any drips for the $1 they cost. Also having a good soft crush washer means you don't have to crank the plug down so tight to stop them from weeping. Then I don't have to take them loose with a pipe wrench and a cheater. :-\ GD Link to comment Share on other sites More sharing options...
91leglift Posted February 29, 2012 Share Posted February 29, 2012 Rick im going to be tearing the engine down tonight. i think ill take you up on your offer to take the block to your guy and have the machining and parts ordered by him and ill assemble it all myself . ill try and make it out and drop it off to you tomorrow if you'll be around Link to comment Share on other sites More sharing options...
Fozester Posted March 1, 2012 Author Share Posted March 1, 2012 Well seems like you have a lot to do Aaron. Depending on what ej25 parts you have, I may need some for my franken motor if I can get around to doing it. I get paid on friday so I'll be ordering my lights after that if you are still willing to do that welding. Link to comment Share on other sites More sharing options...
91leglift Posted March 1, 2012 Share Posted March 1, 2012 Ya we can do that welding whenever Link to comment Share on other sites More sharing options...
Uberoo Posted March 6, 2012 Share Posted March 6, 2012 how come you didn't have a skidplate? thats mandatory for offroad.Heck around here its mandatory on the street. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now