chaseman Posted March 26, 2012 Share Posted March 26, 2012 (edited) Okay so on my 86 GL EA82 5MT it seems to have this plate holding the input bearing in and all the take aparts of 5mt's I find have no plate on the input shaft. Instead where the plate, is instead it seems the case simply does what the plate did. So how I got my tranny is it looks like someone tried to take it off and I can't get it to seat again. Edited March 26, 2012 by chaseman Link to comment Share on other sites More sharing options...
GeneralDisorder Posted March 26, 2012 Share Posted March 26, 2012 That's a standard dual-range front input shaft bearing setup. They all look like that. Someone probably tried to get at the front input shaft seal - but you can't get to it from there. The plate does have bolts on the outside but there is no way to remove it without splitting the case and taking out the snap ring that holds the input shaft bearing into that front bearing holder/quill plate. GD Link to comment Share on other sites More sharing options...
chaseman Posted March 26, 2012 Author Share Posted March 26, 2012 oh okay thanks , i musta been lookin at single range or ej ones. That makes sense having to spilt the case. Also i don't want to take the shaft out , i wanna get it back in. The plate stops about a quarter inch from seating against the case. Does it need pressed or tapped in? Or do i need to man up and split the case? Link to comment Share on other sites More sharing options...
WoodsWagon Posted March 26, 2012 Share Posted March 26, 2012 They probably tried pulling it for a reason, that probably being the input shaft seal leaking. It's not hard to split the case as long as you keep track of how everything lines up so you can get it back together. The hardest part is getting the shift yoke off the shifter shaft depending on how rusted it is. Link to comment Share on other sites More sharing options...
ivans imports Posted March 26, 2012 Share Posted March 26, 2012 Spilt the case the low range is expanded has to come apart its a good trany to learn on ive done a cupple hundred and there a ***************. Take note of how the shifter interlocks go they are hard to put back together Link to comment Share on other sites More sharing options...
Gloyale Posted March 26, 2012 Share Posted March 26, 2012 oh okay thanks , i musta been lookin at single range or ej ones. That makes sense having to spilt the case. Also i don't want to take the shaft out , i wanna get it back in. The plate stops about a quarter inch from seating against the case. Does it need pressed or tapped in? Or do i need to man up and split the case? Yeah, the single range EA and EJ cases don't have that. Don't just hammer or press. The D/R mechanism has expanded, and likely the oiler plate (sheet metal shim) for the D/R gears has probably come out of place too. I made a thread about replacing the front bearing and seal of a S/R case. Search for that, and it'll give you a good idea of what's going on in there. I also have a thread about a 4.11 D/R AWD.......in the end it only kinda worked....but lots of good pics in there too. Just remember....don't disassemble the whole tailsection. Remove the shifter knuckle, disconnect the D/R lever from the front of the case. Pull the inspection plate on top, and using a 1/4 drive, 10mm socket + ratchet and a skinny extension to remove the reverse lockout bolt. rotate the shift rod CC then remove the whole tailsection as one piece. Link to comment Share on other sites More sharing options...
chaseman Posted March 28, 2012 Author Share Posted March 28, 2012 (edited) well , got the case apart and here are the results and I'm gonna go out on a limb and say the say the broken stuff is my D/R gear set. what now? Well Actually I guess next to remove the snap ring on the input shaft so I can get deeper. Just gotta go get those fancy pliers Edited March 28, 2012 by chaseman Link to comment Share on other sites More sharing options...
WoodsWagon Posted March 28, 2012 Share Posted March 28, 2012 The gearset might still be OK, but the synchro blocking ring and the shift collar look like someone tried to beat them together with a sledgehammer. Link to comment Share on other sites More sharing options...
chaseman Posted March 28, 2012 Author Share Posted March 28, 2012 argh, the guy before me didn't have a clue what he was doing. Are they replaceable parts? Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now