Recian Posted July 6, 2012 Share Posted July 6, 2012 Im curious if this is just a characteristic of the AWD car but my impreza when i take u-turns or tight turns in 2nd gear (usually 10-15 mph) it'll bog very low and lose all power or it'll buck really bad where you've gota push in the clutch throw it in 1st and stomp the gas to keep it from bucking over 3000rpm. If you let the clutch out too fast (almost like dumping on a 2wd but not so aggressive) it'll buck like that too. Im wondering if this is just a characteristic of AWD or do i have a MAF problem? Link to comment Share on other sites More sharing options...
987687 Posted July 6, 2012 Share Posted July 6, 2012 manual tranny, I assume? It sounds like the center diff is going bad and starting to seize up. Link to comment Share on other sites More sharing options...
robm Posted July 6, 2012 Share Posted July 6, 2012 Sounds more like torque bind. Link to comment Share on other sites More sharing options...
987687 Posted July 6, 2012 Share Posted July 6, 2012 Sounds more like torque bind. Right, that's what happens when the center diff in a 5speed starts to get tired and bind up. Link to comment Share on other sites More sharing options...
Recian Posted July 7, 2012 Author Share Posted July 7, 2012 (edited) Makes sense seeing as when i back up out of a parking space and cut the wheels it'll stop. So i'm looking at a trans overhaul then Just out of curiosity could this be the same reason after going over speed bumps the car kinda rocks a little, if you give it gas it'll buck and jump back and forth really bad like bad motor mounts which i just replaced with a set of megan racing ones. Runs better but didnt fix that issue. How much do they run on average if you can find them? i can find 02+ WRX ones but not pre 02 Edited July 7, 2012 by Recian Link to comment Share on other sites More sharing options...
WoodsWagon Posted July 7, 2012 Share Posted July 7, 2012 You don't need to overhaul the transmission or even remove it from the car to replace the center diff. You take out the rear driveshaft, the shift coupler, and unbolt the rear cover of the transmission. Pull that off and the center diff and transfer gears come out with it. It's an evening job if you have a pit or a lift, a weekend job if you're on your back in the driveway. Link to comment Share on other sites More sharing options...
1 Lucky Texan Posted July 7, 2012 Share Posted July 7, 2012 Im curious if this is just a characteristic of the AWD car but my impreza when i take u-turns or tight turns in 2nd gear (usually 10-15 mph) it'll bog very low and lose all power or it'll buck really bad where you've gota push in the clutch throw it in 1st and stomp the gas to keep it from bucking over 3000rpm. If you let the clutch out too fast (almost like dumping on a 2wd but not so aggressive) it'll buck like that too. Im wondering if this is just a characteristic of AWD or do i have a MAF problem? are you running different size, model, brand or have mixed new and worn tires? if so, remedy that first. otherwise - yeah, what ^^^ they said. Link to comment Share on other sites More sharing options...
edrach Posted July 7, 2012 Share Posted July 7, 2012 What year Impreza? Center diff changed in '97. Just find a junkyard Impreza of the right year and find one that has significant front end damage (or other damage that resulted in winding up in the junkyard). Pull the rear section off the transmission and install it on your car. Just don't forget to replace the gear oil after you're finished. The center diff from the '97 and up models will cost around $600 from the dealer. Much easier and cheaper to just replace the whole housing. By the way any Legacy and Impreza of the same vintage will work just fine. Has nothing to do with being 4.111 or 3.900 since the center diff is the same for both. Link to comment Share on other sites More sharing options...
Recian Posted July 7, 2012 Author Share Posted July 7, 2012 so the center diff isnt the actual diff like everywhere i've found says, it's just the tailshaft of the transmission then? Link to comment Share on other sites More sharing options...
Ricearu Posted July 7, 2012 Share Posted July 7, 2012 its easier to swap the complete tail housing. you can swap only the center diff. I would grab a junkyard tail housing and be on your marry way. Link to comment Share on other sites More sharing options...
Recian Posted July 7, 2012 Author Share Posted July 7, 2012 Itll be awhile. I got the last 5 speed awd in the area within 50 miles of here. And with consistant days with 110+ heat index ill wait to lay under a junkyard car lol Link to comment Share on other sites More sharing options...
edrach Posted July 7, 2012 Share Posted July 7, 2012 so the center diff isnt the actual diff like everywhere i've found says, it's just the tailshaft of the transmission then?Yes, and it is easier to replace the entire unit rather than just the center diff portion. Link to comment Share on other sites More sharing options...
edrach Posted July 7, 2012 Share Posted July 7, 2012 so the center diff isnt the actual diff like everywhere i've found says, it's just the tailshaft of the transmission then?Essentially yes. Link to comment Share on other sites More sharing options...
987687 Posted July 7, 2012 Share Posted July 7, 2012 Makes sense seeing as when i back up out of a parking space and cut the wheels it'll stop. So i'm looking at a trans overhaul then Just out of curiosity could this be the same reason after going over speed bumps the car kinda rocks a little, if you give it gas it'll buck and jump back and forth really bad like bad motor mounts which i just replaced with a set of megan racing ones. Runs better but didnt fix that issue. How much do they run on average if you can find them? i can find 02+ WRX ones but not pre 02 It could be transmission mount, dog bone, and the other one I've seen give a lot of driveline slop is the trailing arm bushings. Link to comment Share on other sites More sharing options...
jarl Posted July 8, 2012 Share Posted July 8, 2012 As mentioned before, but maybe not stressed enough: make sure the PERIMETER of your tires are all within 1/4" Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now