vtscooby Posted July 20, 2012 Share Posted July 20, 2012 SPONGY Subaru Loyale Brakes!???? This problem is notorious with the Loyale Hill Holder systems... I am surprised there are not more Threads on this issue/problem... Looking for advice on Bleeding the brake system of a 94 Loyale! I have worked on many of these cars, NOT a nuby to auto mechanics... Every now and then I run into a Loyale that it seems, you just can't get the pedal back after bleeding the brakes... All lines inspected, replaced-- Not loosing any fluid...? Clear Bleeder hose shows NO air in fluid when bleeding the system? Plenty of volume pushed through to get normal air out of the lines... Does the Hill Holder Cylinder have air stuck into it? Thoughts on removing it from the system...? Thanks in advance for your time and consideration! vtscooby Link to comment Share on other sites More sharing options...
mikaleda Posted July 20, 2012 Share Posted July 20, 2012 i think the hill holder system is mechanical they usually are. Link to comment Share on other sites More sharing options...
skishop69 Posted July 20, 2012 Share Posted July 20, 2012 Doubt seriously it's the hill holder. It is simply a one way valve to stop fluid from returning to the master cylinder when you release the pedal. I would suspect the master is bypassing internally. Older master cylinders can be prone to this when collapsing calipers or pressure bleeding the system. It causes the seal inside the bore to roll over on itself or split, or you end up with debris in the bore. Either way, new master cylinder..... Link to comment Share on other sites More sharing options...
l75eya Posted July 20, 2012 Share Posted July 20, 2012 It's become just as notoriously apparent that the gl and loyale cars have a bit of a spongy brake pedal feel. It's just a characteristic. You get used to it. (So long as it's safe. If you're hitting the brakes and your car is not stopping safely, that's another issue). I tried for a good month to get the brake pedal to feel firm in a 93 loyale and then just gave up. Brakes work fine. Link to comment Share on other sites More sharing options...
maozebong Posted July 21, 2012 Share Posted July 21, 2012 replacing all the rubber hoses at each wheel helps immensely, especially if they are all original hoses. i have also found out that having the clutch pedal in helped get mine more firm. but yeah, they are still softer than one would expect. Link to comment Share on other sites More sharing options...
mikaleda Posted July 21, 2012 Share Posted July 21, 2012 It's become just as notoriously apparent that the gl and loyale cars have a bit of a spongy brake pedal feel. It's just a characteristic. You get used to it. (So long as it's safe. If you're hitting the brakes and your car is not stopping safely, that's another issue). I tried for a good month to get the brake pedal to feel firm in a 93 loyale and then just gave up. Brakes work fine. my 80 gl doesn't feel spongy at all, at least it didn't before i put a napa brake caliper on it. Link to comment Share on other sites More sharing options...
Loyale 2.7 Turbo Posted July 22, 2012 Share Posted July 22, 2012 Well... my Subaru "BumbleBeast" Brakes Never felt spongy, nor even having the Rear e-Brake retrofitted... it could be a Bad Bleeding procedure issue. Remember that those subarus has a cross pattern on the Brake Lines, so you must start to Bleed from the wheel in the rear that is more far from the Master Cylinder: it is the Rear Passenger's side Wheel, which shares circuit with the Front Driver's Wheel; the other two are on their circuit... if you Search, you'll find the Info here. My own experience teached me to do Two Complete Bleedings on Loyales: the second one usually one day after the firts one, that gets Rid of the Spongy Brake Pedal feeling. Kind Regards. Link to comment Share on other sites More sharing options...
mikaleda Posted July 22, 2012 Share Posted July 22, 2012 that is right you have to follow that procedure or you can't completely purge the air from your system. like you said sometimes it takes two tries to get it right. i'm almost sure that is what is wrong with my gl Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now