Idasho Posted October 7, 2012 Share Posted October 7, 2012 When it comes to trans mounts and the crossmember, I thought I read time and time again that you have to fabricate mounts? I realize that the ea82 mounts are superior, but it seems that the ea81 4-speed mounts work just fine. With the only exception being youd have to drill one more hole for the bracket to match the trans The drivers side bolts up 100% Passenger side needs one hole drilled to make things work. Link to comment Share on other sites More sharing options...
bratman18 Posted October 7, 2012 Share Posted October 7, 2012 I think it may have to do with where it sits once you try to bolt it up to the car, but I'm not positive. Link to comment Share on other sites More sharing options...
AdventureSubaru Posted October 8, 2012 Share Posted October 8, 2012 x2. I'm dipping into the archives of my brain but I believe the 5 speed is longer than the 4. So it bolts to the trans fine, but wont line up one the bod correctly when it's all bolted together. Link to comment Share on other sites More sharing options...
Idasho Posted October 8, 2012 Author Share Posted October 8, 2012 Nope, thats not it. Both the 4-speed and the 5-speed mounts are 17.5" from the face of the bellhousing. And for the record, the 5-speed is considerably SHORTER than the 4-speed Link to comment Share on other sites More sharing options...
djellum Posted October 8, 2012 Share Posted October 8, 2012 were they talking about the bearing on the drive line? Ive heard that it is in a different spot for the different length drivelines. Link to comment Share on other sites More sharing options...
soobiefreak85 Posted October 8, 2012 Share Posted October 8, 2012 It is my understanding that the whole cross member has to be fabricated for the 5-speed. Jerry (bratsrus1) does them for like $100. The only other change is the driveline length. Link to comment Share on other sites More sharing options...
Idasho Posted October 8, 2012 Author Share Posted October 8, 2012 It is my understanding that the whole cross member has to be fabricated for the 5-speed. Not with a lift. IIRC, the only reason a custom crossmember would be needed in a non-lifted rig is to drop the trans enough to clear the tunnel. Link to comment Share on other sites More sharing options...
Leeroy Posted October 8, 2012 Share Posted October 8, 2012 (edited) Idasho this guy did basically the same (OK there was cutting and welding!): cardomain link Others have mentioned elongating the holes in the mounts (and the crossmember too) to make them fit. So I would assume it works as you have done... Edited October 8, 2012 by Leeroy Link to comment Share on other sites More sharing options...
wallaby Posted October 8, 2012 Share Posted October 8, 2012 sorry posted this in your 'rides' thread. EA81 mounts work fine, you are correct in that drill another hole and bolt 'em up i used old ones and filled the gaps with 3m window weld urethane to add some beefiness - you could buy new ones too i guess i used all the 5 speed shift linkages and interior trim i had to space the crossmember down about 1/4" to clear the tunnel no bashing and no lift had to cut a quarter sized triangle out of the back of the hole in the floor 5 speed is shorter so you either need a custom 1 piece driveline - that what i did or you use a EA82 2 peice and figure out how to mount the carrier bearing this is the 2nd easiest swap i ahve ever done on any vehicle (easiest was the rear discs) let me know if you want to come look at mine and also if you want to get rid of the 4speed you might be able to help figure out the wiring for the 4x4 and the reverse lights.....????? 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now