porcupine73 Posted October 14, 2012 Share Posted October 14, 2012 Ok, so '95-'99 Legacy alt runs around $99 because of that recall on them, while for '90-'94 is $219. How do you use a '95-99 in a '94 application? The '94 looks to have three wires connected at the alt connector. The '96 looks to have only two. I haven't had a chance to check the wiring diagrams ... 23700AA090R1 Legacy 1990-1994 Engine Parts, Alternator ALTERNATOR ASSEMBLY REMAN FOR 1990-1994 LEGACY ALL (We will buy back the core in the box for 30 dollars after the job is done, contact us by email and we will arrange) $300 $219 23700AA34ARA Legacy 1995-1999 Engine Parts, Alternator ALTERNATOR ASSEMBLY REMAN FOR 1995-1999 LEGACYS (We will buy back the core in the box for 30 dollars after the job is done, contact us by email and we will arrange) $129 $99 Link to comment Share on other sites More sharing options...
MilesFox Posted October 14, 2012 Share Posted October 14, 2012 (edited) I used a 1st gen legacy alt in a 2nd gen by making jumpers with spade terminals. IT only needed 2 wires and the rest were unused. I almost blew stuff up figuring out which ones, though. Don't cook anything. Perhaps cross-reference schematics. Edited October 14, 2012 by MilesFox Link to comment Share on other sites More sharing options...
porcupine73 Posted October 14, 2012 Author Share Posted October 14, 2012 Ok thanks, I will definitely take a look, this '94 alt is definitely funky. It appears to be the original. I only started it a couple times in the summer and the voltage wouldn't go above maybe 12.8V. Then I just went to start her today and the battery was just about dead (new battery last year). So I put the quick charger on her, and then after about 45 minutes started her up. Voltage stayed up near 14V no matter if I turned the lights, rear defroster, blower, etc. so that makes me suspect of this alt. Last winter I had to double foot her at stop lights if i had much accessories on to keep the voltage from dropping below like 11 volts. Link to comment Share on other sites More sharing options...
pamike Posted October 15, 2012 Share Posted October 15, 2012 have any info on this recall? i have a 96 and would like to know more Link to comment Share on other sites More sharing options...
porcupine73 Posted October 15, 2012 Author Share Posted October 15, 2012 Yes it was a recall because something about a brush or something could let loose at high rpm and then if the driver doesn't notice, the risk was the vehicle could stall in traffic, so they recalled them. I don't remember the # off hand but it's out there. Link to comment Share on other sites More sharing options...
avk Posted October 15, 2012 Share Posted October 15, 2012 Consult the diagrams, unless someone tells you exactly what to do. You know what they say: two wire hook-up, three wire f-up. Link to comment Share on other sites More sharing options...
Fairtax4me Posted October 16, 2012 Share Posted October 16, 2012 have any info on this recall? i have a 96 and would like to know more I don't think it's in effect anymore, but Subaru did end up with a boatload of bad alternators which they sent off to be re-manufactured and they're now for sale at most Subaru dealers for about $75 plus core. That's about $50 - $100 cheaper than the parts store POS alternatives. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted October 16, 2012 Share Posted October 16, 2012 Simple - don't hookup the yellow wire. The 90-94 alt requires an ignition switched 12v lead that the 95+ alt does not. Therefore you simply don't use the yellow, switched 12v lead when you do the swap. Wrap it in the harness so it can't short to anything. GD Link to comment Share on other sites More sharing options...
eulogious Posted October 16, 2012 Share Posted October 16, 2012 Simple - don't hookup the yellow wire. The 90-94 alt requires an ignition switched 12v lead that the 95+ alt does not. Therefore you simply don't use the yellow, switched 12v lead when you do the swap. Wrap it in the harness so it can't short to anything. GD This is exactly what I did when I put a 97 alt into my 90 leggy. Been about a year, no problems at all! Link to comment Share on other sites More sharing options...
eulogious Posted October 16, 2012 Share Posted October 16, 2012 have any info on this recall? i have a 96 and would like to know more Lookup my thread when I did this. All the info about the recall is there, including the actual part numbers for the recall alt... It was a pain to track down and get for $79! Link to comment Share on other sites More sharing options...
porcupine73 Posted October 20, 2012 Author Share Posted October 20, 2012 Simple - don't hookup the yellow wire. The 90-94 alt requires an ignition switched 12v lead that the 95+ alt does not. Therefore you simply don't use the yellow, switched 12v lead when you do the swap. Wrap it in the harness so it can't short to anything. GD Excellent, thank you all, I will try this out. I am very suspicious of the alt on this '94, it appears to be original, and it seems to really charge well at idle only about 50% of the time. It likes to sit below 12.8V output about half the time idling, and about 14V the other half (all at no load). Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now