GTlegs Posted November 8, 2012 Share Posted November 8, 2012 Hi, Does anyone have a clear photo of where the accelerator cable is anchored next to the stock hitachi carb on a 1600? I just cant find where its little tie down bracket is supposed to bolt down - manifold, carb, where Thanks in advance. Link to comment Share on other sites More sharing options...
moosens Posted November 8, 2012 Share Posted November 8, 2012 In my mind it's about 6 inches rear of the carb. Easiest seen and worked from passenger side. Take the spare out to assist but I think you can get it with the spare in. I just had my hands on it when I swapped my pedal box. I might be getting my old 78 at lunch. I'll get my nose in there and get back. Snow here! Snow Shark time !!! Link to comment Share on other sites More sharing options...
Leeroy Posted November 8, 2012 Share Posted November 8, 2012 Although my 1600 has a Weber the brackets and components are the same as the Hitachi: Link to comment Share on other sites More sharing options...
moosens Posted November 8, 2012 Share Posted November 8, 2012 Thanks Lee ! Still nasty out here but I do now have my 78 out eating snow. Cheers! Link to comment Share on other sites More sharing options...
GTlegs Posted November 8, 2012 Author Share Posted November 8, 2012 Thanks for the awesome closeups Lee, however my manifold is a bit different to yours, with the thermostat housing behind the carb, not to the side of it, so I think the bracket must be different! I'll post a pickie on weekend. Link to comment Share on other sites More sharing options...
Leeroy Posted November 8, 2012 Share Posted November 8, 2012 Perhaps it is an earlier manifold, I can take photos of my EA63 1400 (thermostat is in the middle) but basically the bracket for the accelerator cable mounts behind one of the bolts for the thermostat housing. Link to comment Share on other sites More sharing options...
GTlegs Posted November 9, 2012 Author Share Posted November 9, 2012 Perhaps it is an earlier manifold, I can take photos of my EA63 1400 (thermostat is in the middle) but basically the bracket for the accelerator cable mounts behind one of the bolts for the thermostat housing. Yes please! Link to comment Share on other sites More sharing options...
Leeroy Posted November 9, 2012 Share Posted November 9, 2012 Do these help? Link to comment Share on other sites More sharing options...
GTlegs Posted November 9, 2012 Author Share Posted November 9, 2012 Sweet! thats spot on thanks. Link to comment Share on other sites More sharing options...
GTlegs Posted November 11, 2012 Author Share Posted November 11, 2012 Just looked around and I dont seem to have this bracket. You wouldnt have a spare one by any chance please? Link to comment Share on other sites More sharing options...
Leeroy Posted November 11, 2012 Share Posted November 11, 2012 I should have one around somewhere! I will check and let you know. Link to comment Share on other sites More sharing options...
GTlegs Posted November 11, 2012 Author Share Posted November 11, 2012 I should have one around somewhere! I will check and let you know. Thanks! Link to comment Share on other sites More sharing options...
Leeroy Posted November 12, 2012 Share Posted November 12, 2012 OK I found one. It is a bit rough as it needed to bent back into shape (not sure why!) and the only spare clamp I had was from the choke but it should do the job. Yours if you want it, send me a PM with your address and I will mail it to you. Link to comment Share on other sites More sharing options...
GTlegs Posted November 12, 2012 Author Share Posted November 12, 2012 OK I found one. It is a bit rough as it needed to bent back into shape (not sure why!) and the only spare clamp I had was from the choke but it should do the job. Yours if you want it, send me a PM with your address and I will mail it to you. Its all good! Thanks, PM sent. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now