the sucker king Posted February 17, 2013 Share Posted February 17, 2013 To remove the crank pully, there are no good holes in the drive plate to stick a screwdriver, what the trick to locking it? Link to comment Share on other sites More sharing options...
MilesFox Posted February 17, 2013 Share Posted February 17, 2013 Pop off the little rubber timing plug on the bell housing and jam a prybar in there. More easily done that with a manual transmission. There is a part number for a ring gear locking tool to hold the flywheel still. I would imagine it could work the same for the torque converter. I'm not sure where you would go about getting one, unless you can order it through the dealer's special tool list. Link to comment Share on other sites More sharing options...
the sucker king Posted February 17, 2013 Author Share Posted February 17, 2013 Pop off the little rubber timing plug on the bell housing and jam a prybar in there. More easily done that with a manual transmission. Jam a prybar in where? There are no real holes in the driveplate. Link to comment Share on other sites More sharing options...
MilesFox Posted February 17, 2013 Share Posted February 17, 2013 There are, you should use something flat like a long screwdriver or some sort of stiff piece of flat metal. you will have holes whre the bolts hold the flexplate to the torque converter. Link to comment Share on other sites More sharing options...
the sucker king Posted February 17, 2013 Author Share Posted February 17, 2013 thank you sir, I shall move on this first daylight Link to comment Share on other sites More sharing options...
l75eya Posted February 17, 2013 Share Posted February 17, 2013 On the top of the transmission, where the spare tire goes, there's a little rubber plug. Pull off the plug, rotate the crank a bit until you see a bolt on the flywheel. I threw a box-wrench on the bolt, slowly turned the crank until it was up against the transmission housing, and then went to town taking off the crank pulley bolt. Worked like a charm. Link to comment Share on other sites More sharing options...
MilesFox Posted February 17, 2013 Share Posted February 17, 2013 ^^^This will work. You can also put a deep socket on the bolt to hold it still against the bellhousing window. This might be easiest with a 2nd hand to help. Good luck. Another trick to loosen the bolt is to ise a long breaker bar and but it against the battery side of the frame, and bump the starter. be sure to unplug the coil! this works for loosening, but you will hae to resort to the wrench in the hole to tighten it. Make sure to get it good and tight so the bolt doesn't walk out after it is running. Link to comment Share on other sites More sharing options...
l75eya Posted February 17, 2013 Share Posted February 17, 2013 Definitely recommended that you use a breaker bar with a nice long pipe on it. Idk the bumping the starter idea always scared the * out of me. If you do bump the starter, make sure that wrench is on that bolt good haha. And yeah, disconnect the coil. Wouldn't be good to have the motor running with a wrench attached to the crank pulley bolt. Look out!!! lol Link to comment Share on other sites More sharing options...
NickNakorn Posted February 17, 2013 Share Posted February 17, 2013 Alternative access to the ring-gear on the flywheel can be had by removing the starter-motor and using a large screwdriver or pry-bar in the ring-gear to block the flywheel. Depending on the length of the breaker-bar on the socket on the crank-pulley bolt , you might need a helper or very, very long arms! Link to comment Share on other sites More sharing options...
Gloyale Posted February 17, 2013 Share Posted February 17, 2013 Use locktite removable on the crank bolt. Helps ensure it won't walk out Link to comment Share on other sites More sharing options...
Uberoo Posted February 18, 2013 Share Posted February 18, 2013 If the goal is to remove the crank pulley why not put a socket and a breaker bar on the nut and position the breaker bar to its on a "framerail" in the direction the engine spins,and then bump the starter. Link to comment Share on other sites More sharing options...
NickNakorn Posted February 18, 2013 Share Posted February 18, 2013 Uber, I've witnessed a couple of accidents with people trying that - luckily no serious harm but it really can go wrong. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now