NorthCoast Posted March 11, 2013 Share Posted March 11, 2013 Engine starts and idles fine but bogs out and dies at 1500 RPM. I pulled the timing belt covers off to check the timing marks on the cams and it "looks" like it's still right. Swapped out the cam sensor to see if that was the problem but no change. When idling the left cam pulley looks like it might be wobbling slightly but could be an optical illusion. I checked the pulley to see if there was any play but it was solid. Any ideas? Link to comment Share on other sites More sharing options...
mikaleda Posted March 11, 2013 Share Posted March 11, 2013 IMHO I would start by verifying that you have the correct fuel pressure. Also if it has been a long time since you have changed the fuel filter that might be a good thing to do to. Link to comment Share on other sites More sharing options...
1 Lucky Texan Posted March 11, 2013 Share Posted March 11, 2013 does it run if you get above 1500rpm? assuming good 'tune-up' parts and general condition, maybe a TPS problem. Link to comment Share on other sites More sharing options...
NorthCoast Posted March 11, 2013 Author Share Posted March 11, 2013 Fuel filter was my first thought but no change after being replaced. TPS was recently gone through as well. Link to comment Share on other sites More sharing options...
1 Lucky Texan Posted March 11, 2013 Share Posted March 11, 2013 did this begin slowly? any work done immediately prior to the problem? Link to comment Share on other sites More sharing options...
NorthCoast Posted March 11, 2013 Author Share Posted March 11, 2013 No work done prior and the onset was sudden. Link to comment Share on other sites More sharing options...
Cougar Posted March 11, 2013 Share Posted March 11, 2013 You might have a problem with the MAF sensor. Check the fuel pressure and make sure that is okay also. If those things are good then I would check the compression to see if there is a valve timing issue. Link to comment Share on other sites More sharing options...
1 Lucky Texan Posted March 11, 2013 Share Posted March 11, 2013 (edited) kinda wondering about a possible clogged cat. conv. or other exhaust restriction. vacuum gauge test might show that. Edited March 11, 2013 by 1 Lucky Texan Link to comment Share on other sites More sharing options...
NorthCoast Posted March 11, 2013 Author Share Posted March 11, 2013 Exhaust was just redone so no issues there. Link to comment Share on other sites More sharing options...
CoupedUpSubie Posted March 11, 2013 Share Posted March 11, 2013 I would suggest pulling a couple spark plugs and looking to see if they are covered in fuel or not, also check the plug gap. Another piece of information is what plugs do you have in it? Some are known to cause problems. Then go to your MAF and airfilter. Get a can of MAF sensor cleaner and clean the MAF sensor(even if you don't have a code, its still a good idea to do on occasion). Also check fuel pressure as engine rpm is increased, pump might not be putting out enough fuel as the demand is increased. Link to comment Share on other sites More sharing options...
Gloyale Posted March 12, 2013 Share Posted March 12, 2013 PVC or IAC tubes disconnected? Link to comment Share on other sites More sharing options...
ivans imports Posted March 12, 2013 Share Posted March 12, 2013 +1 maf senser or feul preshure Link to comment Share on other sites More sharing options...
NorthCoast Posted March 17, 2013 Author Share Posted March 17, 2013 Fuel pressure 32. Swapped MAF and ECU. No change. New plugs. No change. All vac and pressure lines attached. New timing belt. No change. The only thing I've found out of spec is IAC resistance. 10.5 instead of 9. Would this cause the issue or am I missing something. Link to comment Share on other sites More sharing options...
Gloyale Posted March 17, 2013 Share Posted March 17, 2013 gotta be an unmetered air leak. PCV hoses, and IAC tube double check for cracks maybe put clamps on them. Link to comment Share on other sites More sharing options...
NorthCoast Posted March 18, 2013 Author Share Posted March 18, 2013 Negative. 1 Lucky Texan got it right. Clogged cat. I put my wheelin exhaust on because that was the only thing I hadn't tried and it loved it. So frustrating but at least I can go wheeling next weekend. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now