jonas Posted May 11, 2013 Share Posted May 11, 2013 Height, Width, Length, Depth. Gen 1 and Gen 2. Looking to see if I can stuff a set and still keep my rollbar. Link to comment Share on other sites More sharing options...
djellum Posted May 11, 2013 Share Posted May 11, 2013 what roll bar do you have? the normal one with the 2 front pillars and the support pillars that go to the wheel humps? the one we did for Shadabobs brat (you can see it in readers rides) fit a full sized spare under the jump seats, and it also has the roll bar, so Im pretty sure it will. I dont know where he got his roll bar though so check the pictures out. Link to comment Share on other sites More sharing options...
jonas Posted May 11, 2013 Author Share Posted May 11, 2013 (edited) http--,,--// I believe It's off of a ford ranger trimmed up to fit Brat. Seems a little tight where the jumpseats would go. I'm thinking I may have to trim up the seat frame a bit, if possible, to make it fit. I hope not. Edited May 11, 2013 by jonas Link to comment Share on other sites More sharing options...
djellum Posted May 11, 2013 Share Posted May 11, 2013 I cant measure since I dont have one, but heres a link to a guy with a bright blue roll bar installed and the seats with it. should give you some idea of spacing (best pic is about halfway down). he doesnt have the headrests so if you want those you have to add about 6 inches of height, but I still think it will clear. http://www.ultimatesubaru.org/forum/topic/129380-subaru-brat-1985-restoration/ Link to comment Share on other sites More sharing options...
jonas Posted May 12, 2013 Author Share Posted May 12, 2013 Thanks. If someone could post some really close-up shots that would help. Link to comment Share on other sites More sharing options...
turbosubarubrat Posted May 12, 2013 Share Posted May 12, 2013 if you can take some pics i can probably tell you if it will fit heres some of the ones i've put together 79 brat 1978 brat 1985 brat Link to comment Share on other sites More sharing options...
turbosubarubrat Posted May 12, 2013 Share Posted May 12, 2013 im going to say it looks like it would fit with a factory frame but you might have to take the seats off then put the frame in then bolt the seats back on to the frame. but i would say a few more picks would make it easier to tell. Link to comment Share on other sites More sharing options...
jonas Posted May 12, 2013 Author Share Posted May 12, 2013 Cool, thanks. I'll get some pics up tomorrow. My tubes are fatter and it's a gen 2 which I believe is a bit wider than the Gen 1's but it's looking like I can make a set fit with little to no modding. Link to comment Share on other sites More sharing options...
jonas Posted May 12, 2013 Author Share Posted May 12, 2013 http--,,--// http--,,--// Link to comment Share on other sites More sharing options...
jonas Posted May 12, 2013 Author Share Posted May 12, 2013 http--,,--// http--,,--// Looks do-able. Tight fit but do-able. They wouldn't be for riding in anyways... Link to comment Share on other sites More sharing options...
jonas Posted May 12, 2013 Author Share Posted May 12, 2013 http--,,--// One more....... Link to comment Share on other sites More sharing options...
jonas Posted May 12, 2013 Author Share Posted May 12, 2013 I'm thinking remove the bar, install the seat frame, drop bar back in, then put the seats in. Probably have to move the seats a little closer together. There's about a 2 inch gap between the bar and the bed. Link to comment Share on other sites More sharing options...
turbosubarubrat Posted May 13, 2013 Share Posted May 13, 2013 looks like a tight fit but you can always cut and weld if worst comes to worse. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now