judymayo Posted June 20, 2013 Share Posted June 20, 2013 my 2006 subaru forester won't start after overheating symptoms:spark, fuel, compression Link to comment Share on other sites More sharing options...
ivans imports Posted June 20, 2013 Share Posted June 20, 2013 timing belt jump ? or valves droped or wire harness melted or unrealated feul pump problem or is just cooked how hot did it get Link to comment Share on other sites More sharing options...
mikaleda Posted June 20, 2013 Share Posted June 20, 2013 How badly was it overheated, did it just stop running from being over heated or did you see the gauge redlining and shut it off. That can make a huge differance. How long did you wait to restart it? By "symptoms spark, fuel, compression" do you mean you are missing all of those? Link to comment Share on other sites More sharing options...
judymayo Posted June 20, 2013 Author Share Posted June 20, 2013 cooled it down drove home unable to start since overheating pocket scanner showed no codes except...spark..fuel..compression Link to comment Share on other sites More sharing options...
mikaleda Posted June 20, 2013 Share Posted June 20, 2013 (edited) I don't see how a scanner can say there's no compression, that purely mechanical. You should manually check for compression, it should be at least 120-180, if your getting lower compression than 120 then I would check the timing belt timing. Edited June 20, 2013 by mikaleda Link to comment Share on other sites More sharing options...
bstone Posted June 21, 2013 Share Posted June 21, 2013 cooled it down drove home unable to start since overheating pocket scanner showed no codes except...spark..fuel..compression This isn't English. Link to comment Share on other sites More sharing options...
Godsmulligan Posted June 21, 2013 Share Posted June 21, 2013 This isn't English. Their, their, their, it'll be ok. Link to comment Share on other sites More sharing options...
mikaleda Posted June 21, 2013 Share Posted June 21, 2013 Ya, punctuation would most definatly help. Link to comment Share on other sites More sharing options...
MilesFox Posted June 21, 2013 Share Posted June 21, 2013 Their, their, their, it'll be ok. Their, there, they're 2 Link to comment Share on other sites More sharing options...
1 Lucky Texan Posted June 21, 2013 Share Posted June 21, 2013 Their, there, they're definatly Link to comment Share on other sites More sharing options...
Godsmulligan Posted June 22, 2013 Share Posted June 22, 2013 Their, there, they're Link to comment Share on other sites More sharing options...
ivans imports Posted June 22, 2013 Share Posted June 22, 2013 You guys and your grammer spell it wrong just to mess with them ! Link to comment Share on other sites More sharing options...
timintc Posted June 23, 2013 Share Posted June 23, 2013 um can we all get past English 101 and get back to helping Judy in Tampa? Sounds like a lot going on here spark fuel compression any issue or which would be the cause for your non-start. I have seen so many head gasket failures up here in N Michigan that I would lean toward that assumption. I recently had a 304 code, misfire in the # 4 cylinder, be a lead in to a head gasket failure. Coolant was leaking into the combustion chamber causing the misfire but the car was still running well for a few days until it eventually overheated. Now if you had a catastrophic failure and you had coolant leaking into all the cylinders you would get no spark and no combustion. Just my 2 cents hope my grammer diction and punctuation were sufficient to pass. Link to comment Share on other sites More sharing options...
1 Lucky Texan Posted June 23, 2013 Share Posted June 23, 2013 You guys and your grammer spell it wrong just to mess with them ! 1 Link to comment Share on other sites More sharing options...
heartless Posted June 24, 2013 Share Posted June 24, 2013 cooled it down drove home unable to start since overheating pocket scanner showed no codes except...spark..fuel..compression Not enough information.... First off - we need to know how hot did it actually get... 1. Did the gauge peg out & the motor quit running? 2. Or, did you notice it was getting hot and YOU shut it down? 3. Does fuel get to the engine? 4. Is there spark? 5. Compression - did this get checked manually? these are all yes/no questions... 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now