BlackBoot Posted March 11, 2014 Share Posted March 11, 2014 (edited) my new project, first job timing belt, how different is the procedure from an EA82? Edited March 11, 2014 by BlackBoot 1 Link to comment Share on other sites More sharing options...
ruparts Posted March 12, 2014 Share Posted March 12, 2014 hi, welcome in, i really like these. as for the belts, the job and process is done escentially the same,, same flywheel marks, same cam alignment straight up -straight down, all that is similar. the cam pulleys are real steel not stamped , the belts are a bit wider, the tensioners are similar but not alike the ea82. the one main difference is the left side tensioner setup, it is a piviot mounted roller and there is a plunger that pushes on it to acheve tension. it is called the hydrolic tensioner, in fact it has no hydrolic function at all, it is a wound spring on a threaded plunger inside, if the belt sees slack, the spring unwinds the plunger which pushes on the tension pully piviot. the hard part is that you have to wind up the tensioner and keep it wound while you install it, there is a tool and several trick methods to acheve this. then after all is in place ,, release the tensioner and its automatic. only thing is to make sure all the parts move freely, the piviot needs to be checked , and lubed, and all the pulley bearings good, same as you would an ea-82. double check the alignment by doing a rotation and recheck it all , and done. Link to comment Share on other sites More sharing options...
zukiru Posted March 18, 2014 Share Posted March 18, 2014 Nice car! Link to comment Share on other sites More sharing options...
BlackBoot Posted May 30, 2014 Author Share Posted May 30, 2014 today I finished the timing belt and got it running, took a spin around the block a couple of times. The Cybrid steering is great. rusty breaks and one warped rotor. the relays for the fans are all screwed up and I cant find a manual anywhere? 1 Link to comment Share on other sites More sharing options...
TomRhere Posted May 31, 2014 Share Posted May 31, 2014 go to subaruxt.com You can find the downloadable manual there in the tech thread. I so miss my '88 XT6. But I have most of it under my '88 GL Wagon. 1 Link to comment Share on other sites More sharing options...
BlackBoot Posted June 26, 2014 Author Share Posted June 26, 2014 I eventually paid $15 for a PDF manual, and I sorted out the relays and AC fuse block. now for some bodywork. I have to sell my 86 GL Coupe to make room for the XT6. Link to comment Share on other sites More sharing options...
BlackBoot Posted July 17, 2014 Author Share Posted July 17, 2014 New pictures, 1 Link to comment Share on other sites More sharing options...
BlackBoot Posted August 1, 2014 Author Share Posted August 1, 2014 Finished the rust removal behind all the mud flaps and under the rockers. smooth out and sanding tomorrow. I hope to have it done for WCSS 1 Link to comment Share on other sites More sharing options...
BlackBoot Posted August 1, 2014 Author Share Posted August 1, 2014 (edited) Dang! that passenger side fender is hell to take off! stupid snorkel and washer fluid tank in the way. much different than a Loyale, the XT has no room for tools except for a box wrench 1/8th of a turn at a time, ugh! and I have a Milwaukee cordless power ratchet and can't get it in there...got fed up with one bolt and got out the chisel and a BFH! Mission accomplished. putting it back on, not so bad, learning curve. Edited August 1, 2014 by BlackBoot Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now