Demon Brat Posted April 25, 2014 Share Posted April 25, 2014 My son and I got his BRAT looking so good we decided to do the motor now. The BRAT sat for at least 10 years so all the oil seals were leaking and the clutch was getting old. With you guys motivation we decided to go all the way. Pulled the motor and going to have the heads looked at, new rings (hope that's all), reseal it, lots of degreasing and resealing the transmission. Hope it doesn't turn into too much. He is really good at taking stuff apart. BEFORE. AFTER Motor in... Motor out... Now the fun begins. taking the heads and block to the machine shop. we'll be cleaning stuff this weekend. I really enjoy these build threads so I'll try to keep it updated. Already broke one part i will need to replace. Anyone have a re-circulation pipe like this? Goes from right side head to the intake. THANKS EVERYONE...WISH US LUCK!! Shawn 2 Link to comment Share on other sites More sharing options...
backwoodsboy Posted April 25, 2014 Share Posted April 25, 2014 Having done a couple EA rebuilds and build threads myself I have a soft spot for this thread. (Im no doubt some of the bad influence) Im staying tuned! Link to comment Share on other sites More sharing options...
Dinky26 Posted April 25, 2014 Share Posted April 25, 2014 Best of luck with your project. Link to comment Share on other sites More sharing options...
sumoco Posted April 25, 2014 Share Posted April 25, 2014 That is one sexy looking brat, I've got a gen 2 brat I'm doing the same on, except I'm cramming an ej22 into it 1 Link to comment Share on other sites More sharing options...
spicypeanut Posted April 25, 2014 Share Posted April 25, 2014 Anything worth doing is worth doing right. So I'll be following along to make sure you do it justice! Link to comment Share on other sites More sharing options...
lvsarge Posted April 25, 2014 Share Posted April 25, 2014 Good luck, bud. I am going to pick up my heads from the machine shop tonight! Can't wait! Link to comment Share on other sites More sharing options...
Demon Brat Posted April 26, 2014 Author Share Posted April 26, 2014 Ivsarge, Just curious, did your heads have the little cracks between the valve? what did you have done to your heads and what did it cost? I have those small cracks, machine shop wasn't real concerned about them. Going to pressure test them first, then surface and clean up the valves. Link to comment Share on other sites More sharing options...
Uberoo Posted April 26, 2014 Share Posted April 26, 2014 If you don't have emission testing that pipe is for the EGR.A little bird once told me that you could fill each threaded end with weld and plug both holes up and not have to deal with finding a new one or the hassle of installing it. Link to comment Share on other sites More sharing options...
lvsarge Posted April 29, 2014 Share Posted April 29, 2014 Yeah, on one head I had tiny cracks, I asked about them and the machinist said they appeared to be casting marks and not to be concerned. The other head didn't have those marks though. As for what I had done, I had the heads tanked, cleaned up, resurfaced, valves grinded, and new oil seals pressed in, cost about $250. Link to comment Share on other sites More sharing options...
Demon Brat Posted April 30, 2014 Author Share Posted April 30, 2014 Starting to clean everything and reading about the AIS (Air Injection System) Wondering, since we did a Weber conversion and we do not have to pass emissions in Iowa, can we lose the AIS? I think it would really clean up the motor's appearance and if the motor doesn't need it, why put it back on. I think we may keep the EGR, have hear and read positives and negatives on the EGR. Can we simple plug the four holes where the AIS screwed in, steel plug...aluminum plug...any thread sealant? Link to comment Share on other sites More sharing options...
Demon Brat Posted May 17, 2014 Author Share Posted May 17, 2014 Good news from the machine shop.. Head were pressure tested and everything looked good. Still installing some wheel seals and stuff and waiting on more news from the machine shop. Project is going well, just need time and other people to get their stuff done. Searched high and low for a clutch fork boot, gonna try and modify and use a 1979 Nissan boot, looks like it will work...let's hope. If it does, I'll let everyone know. Still looking for one more steering billow, got one new but can't find another one. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now