SnatchedHatch Posted May 2, 2014 Share Posted May 2, 2014 (edited) So my clutch gave out on Monday, it was started to slip a lot and finally it gave nothing. My car was pushed into a local lot. The thing is, if I start it up and engage the clutch, it's as if it's NOT there. There is no sound or feeling, yet the pedal has the same tension as normal. What could be the problem? If the clutch plate had been worn down completely, (not out of the question as I mistook clutch slippage as a weak old engine for quite sometime now) would it still be there to have some contact. I don't think the clutch plate is stuck back, no abnormal jerks or feeling. And it could not have burst, it just progressed into massive slippage, then nothing. Please help! Thank you in advance for any advice or comments, -Sam Edited May 2, 2014 by SnatchedHatch Link to comment Share on other sites More sharing options...
Gloyale Posted May 2, 2014 Share Posted May 2, 2014 No friction material left. Pressure plate works which is why pedal feels normal but there is nothing for it to grab. Sounds normal for a burned up clutch. Link to comment Share on other sites More sharing options...
naru Posted May 2, 2014 Share Posted May 2, 2014 I`ve had clutch discs completely disintegrate such that the clutch hub is no longer attached to anything. Link to comment Share on other sites More sharing options...
Stubies Subie Posted May 2, 2014 Share Posted May 2, 2014 I had this happen to mine -> http://s1239.photobucket.com/user/mrlinfoot/media/100_2805.jpg.html 1 Link to comment Share on other sites More sharing options...
markjw Posted May 2, 2014 Share Posted May 2, 2014 (edited) Have you checked to make sure one of your front hubs isn't stripped out? It's worth checking out considering the weird clutch failure. Set your parking brake, start you car, put the tranny in first gear and let the clutch pedal out. Then get out and see if your front axle nut is turning either side. If so, you have a stripped hub. Edited May 2, 2014 by markjw Link to comment Share on other sites More sharing options...
SnatchedHatch Posted May 2, 2014 Author Share Posted May 2, 2014 (edited) Have you checked to make sure one of your front hubs isn't stripped out? It's worth checking out considering the weird clutch failure. Set your parking brake, start you car, put the tranny in first gear and let the clutch pedal out. Then get out and see if your front axle nut is turning either side. If so, you have a stripped hub. The idea of a stripped hub of some sort was floated, I'll definitely take a look at the shafts. Thanks Edited May 2, 2014 by SnatchedHatch Link to comment Share on other sites More sharing options...
SnatchedHatch Posted May 2, 2014 Author Share Posted May 2, 2014 No friction material left. Pressure plate works which is why pedal feels normal but there is nothing for it to grab. Sounds normal for a burned up clutch. I figured it was completely used up, but wouldn't there be contact still? Would the flywheel not be gouged as it cannot reach that far? Link to comment Share on other sites More sharing options...
SnatchedHatch Posted May 2, 2014 Author Share Posted May 2, 2014 I`ve had clutch discs completely disintegrate such that the clutch hub is no longer attached to anything. Ok, I'll check what I am able to. Link to comment Share on other sites More sharing options...
SnatchedHatch Posted May 2, 2014 Author Share Posted May 2, 2014 Is it common for an extremely worn clutch to make no contact whatsoever? Link to comment Share on other sites More sharing options...
Gloyale Posted May 2, 2014 Share Posted May 2, 2014 Is it common for an extremely worn clutch to make no contact whatsoever? Yes. The pressure plate is setup to have a distance, x, between it's face and the Flywheel when it's completely "clamped" The friction disc has a thickness of X + ~.10 ~ .20" so that it takes up all the space between the Fly and PP and gets gripped between them. When the friction material wears to a thickness of Less Than X then you get nothing......disc is sitting in dead space between the Fly and PP. 2 Link to comment Share on other sites More sharing options...
SnatchedHatch Posted May 5, 2014 Author Share Posted May 5, 2014 Didn't expect the cv shafts to be snapped, they weren't. Just the clutch plate given all the helpful descriptions. Thanks Link to comment Share on other sites More sharing options...
gbianchi Posted May 6, 2014 Share Posted May 6, 2014 you could try loosening your cable some before digging into clutch replacement, bought a legy with a '' worn out clutch" loosend the cable alot and drove it home and another 30k then replaced the clutch:) 1 Link to comment Share on other sites More sharing options...
SnatchedHatch Posted May 6, 2014 Author Share Posted May 6, 2014 you could try loosening your cable some before digging into clutch replacement, bought a legy with a '' worn out clutch" loosend the cable alot and drove it home and another 30k then replaced the clutch:) Hmm, I'll pass that message over to the buyer of my hatch (mechanic's special, not fooling anyone with a car that can't drive) Link to comment Share on other sites More sharing options...
SnatchedHatch Posted June 8, 2014 Author Share Posted June 8, 2014 I had this happen to mine -> http://s1239.photobucket.com/user/mrlinfoot/media/100_2805.jpg.html I'm going to have to one-up you! Like I mentioned, I know the guy who bought my Soob, he showed me the clutch plate http://postimg.org/gallery/6aj0woow/ Link to comment Share on other sites More sharing options...
MR_Loyale Posted June 9, 2014 Share Posted June 9, 2014 I'm going to have to one-up you! Like I mentioned, I know the guy who bought my Soob, he showed me the clutch plate http://postimg.org/gallery/6aj0woow/ Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now