gdudik Posted January 8, 2015 Share Posted January 8, 2015 I've got an 86 GL wagon with the 3at that I've successfully converted to SPFI from the hitachi carb, thanks to the help from this forum. Here's what I've got going on: At hot idle, it will idle at about 800, but it mifires pretty regularly. You can hear pops out the exhaust and the engine will shake slightly. Drives well enough. Motor has been completely resealed with head gaskets, OEM intake man gaskets, cam towers sealed properly with OEM o-rings, etc. Timing set at 20 with green plugs plugged. NO VACUUM LEAKS (tested with my homebrew smoke machine) New: Plugs Wires Cap Rotor Coolant temp sensor for computer Timing Belts tensioned properly If I unplug the MAF, it idles perfectly. I'm assuming that's because it forces it rich to compensate for the lack of info from the MAF. If I hook up a timing light, I don't get a perfect pattern of flashes. It will drop out from time to time, and that's when the engine stalls. I don't know if this is a symptom or a cause of the underlying problem. I smogged the car in OR (which is where it needs to be registered) and I'm assuming it failed because of the miss at idle. I got 600s for HC (limit 220), but I'm at .7 (limit 1.0) on CO. I'm leaning towards a weak coil (since a lean mixture is harder to ignite), but possibly a bad CAS. I need to get this thing smogged by the end of January, since that's when the current WA tags expire. Any thoughts? Link to comment Share on other sites More sharing options...
MR_Loyale Posted January 9, 2015 Share Posted January 9, 2015 Checking the coil and grounds is a good place to start. Link to comment Share on other sites More sharing options...
gdudik Posted January 9, 2015 Author Share Posted January 9, 2015 Coil resistance checks out in spec, but I know the ohms don't always tell the whole story. I have an extra ground cable going direct from battery neg to the LH strut tower so it all should be good because I cleaned all the grounds when I installed coil and ignition amplifier. Link to comment Share on other sites More sharing options...
Petersubaru Posted January 10, 2015 Share Posted January 10, 2015 Coil resistance checks out in spec, but I know the ohms don't always tell the whole story. I have an extra ground cable going direct from battery neg to the LH strut tower so it all should be good because I cleaned all the grounds when I installed coil and ignition amplifier. sounds very similar to my experience after my spfi conversion..the car didn't like the timing setting at 20…I first of all checked for vacuum leaks and then used a vacuum gauge as my guide to set the timing…green connectors unplugged..adjusted the idle screw on the electronic idle control switch..been good for many thous. of miles... Link to comment Share on other sites More sharing options...
gdudik Posted January 12, 2015 Author Share Posted January 12, 2015 Well I got ahold of a loyale (mother in law's) that she said I could pull some parts off temporarily to check on the GL. Tried coil, no luck. Tried ignition amp, no luck. Changed whole disty--bingo! Timing light flashes steady with no missed flashes and idle is noticeably better. I still get the occasional pop out the exhaust, but it seems to get worse if I get too far away from 19, which is where I have it set. Petersubaru, do you remember whether you had to advance the timing further or back it off from 20 in order to make it run right? I will set the timing with a vacuum gauge if it doesn't pass again, but the idle is sooo much better. Link to comment Share on other sites More sharing options...
MR_Loyale Posted January 12, 2015 Share Posted January 12, 2015 (edited) If your distributor is the optical pickup style, you can open it up and clean the wheel and sensor with electronic cleaner. Just remove the screw on the dust plate(Don't disassemble beyond that point to ensure nothing is messed up). I did this last summer to mine when I had the engine out. I don't have any misfires. Of course I cleaned mine up for my trip this past summer. Edited January 12, 2015 by MR_Loyale Link to comment Share on other sites More sharing options...
gdudik Posted January 12, 2015 Author Share Posted January 12, 2015 Opened up the dusty and found that the little disc with the slots for the optical sensor was loose on shaft. Distributor is in pieces on my workbench now. Have been unlucky finding an optical sensor from parts places that includes the disc, so I'm stuck with a reman or junkyard disty. Reman distributors are $$$ even with my commercial acct. Anybody know where I can come up with one in the Portland, OR area? Link to comment Share on other sites More sharing options...
Nate E. Posted January 12, 2015 Share Posted January 12, 2015 Hey check these guys out: http://www.philbingroup.com/rebuilt/distributors.htm Maybe he's got parts n stuff. NE Link to comment Share on other sites More sharing options...
gdudik Posted January 12, 2015 Author Share Posted January 12, 2015 Thank you for that. I'll check them out Link to comment Share on other sites More sharing options...
MR_Loyale Posted January 14, 2015 Share Posted January 14, 2015 (edited) Check out row52.com I am sure there are EA82's at the Portland yard. http://row52.com/Vehicle/Index/JF1AC422XNC206424 Edited January 14, 2015 by MR_Loyale Link to comment Share on other sites More sharing options...
flatfourx4 Posted January 14, 2015 Share Posted January 14, 2015 Remember you distributor and block are dissimilar metals as well as bolts. Look for any oxidation on mating surfaces. Sand appropriately and never be afraid to use "Neverseize" on steel bolts that go into aluminum or magniesium. Also, use a little di-electric grease between mating surfaces of block and distributor base. Oxides on these surfaces prevent electrons from flowing (i.e. It prevents proper grounding of current). Good luck and stay thirsty Link to comment Share on other sites More sharing options...
Petersubaru Posted January 18, 2015 Share Posted January 18, 2015 Well I got ahold of a loyale (mother in law's) that she said I could pull some parts off temporarily to check on the GL. Tried coil, no luck. Tried ignition amp, no luck. Changed whole disty--bingo! Timing light flashes steady with no missed flashes and idle is noticeably better. I still get the occasional pop out the exhaust, but it seems to get worse if I get too far away from 19, which is where I have it set. Petersubaru, do you remember whether you had to advance the timing further or back it off from 20 in order to make it run right? I will set the timing with a vacuum gauge if it doesn't pass again, but the idle is sooo much better. Using my "back to zero" timing light ..it reads the timing at 24…the engine has many miles on it which will somewhat affect vacuum …I use mid grade gas... Link to comment Share on other sites More sharing options...
gdudik Posted January 25, 2015 Author Share Posted January 25, 2015 Ok built a good disty out of a couple of old ones, and the idle's much better but not perfect. I even put a gallon and a half of alcohol in it with it on E, and it still won't pass emissions. I've ordered a new cat and Y-pipe, since the old one's an aftermarket anyway and the honeycomb is loose. Also I think where I mounted the O2 sensor is too far out of the stream--it never reports anything over .2 volts, even at 2500 rpm, so I think it's dumping fuel in all the time at cruise. But that doesn't explain my idle misfire. This car is making me tear my hair out. Any ideas? Link to comment Share on other sites More sharing options...
ihscout54 Posted January 25, 2015 Share Posted January 25, 2015 Dude, been there done that! http://www.ultimatesubaru.org/forum/topic/97791-spfid-brat-poor-idle-and-pinging/ Whats ur intake setup like? Fuel pressure readings on both sides of the regulator? Tps readings? Has any one touched the throttle stop screw? Its marked with a gob of paint, and yes it matters. How are you setting your timing? Dont forget those connectors... What was your engine condition befor the swap? Any idea of compression? These were all things that casued me trouble after my swaps. Btw your o2s completed the ten step program befor leaving the factory and no longer likes to drink alcohol. Might be time to try a heated o2s. Where is it? Moot point i suppose as your new cat will have the bung in the converter. 1 Link to comment Share on other sites More sharing options...
DaveT Posted January 25, 2015 Share Posted January 25, 2015 In my experience, an EA82 will not pass emissions without an operating cat system. The OEM has 2, the system I built has 1. Link to comment Share on other sites More sharing options...
gdudik Posted January 25, 2015 Author Share Posted January 25, 2015 Dude, been there done that! http://www.ultimatesubaru.org/forum/topic/97791-spfid-brat-poor-idle-and-pinging/ Whats ur intake setup like? Fuel pressure readings on both sides of the regulator? Tps readings? Has any one touched the throttle stop screw? Its marked with a gob of paint, and yes it matters. How are you setting your timing? Dont forget those connectors... What was your engine condition befor the swap? Any idea of compression? These were all things that casued me trouble after my swaps. Btw your o2s completed the ten step program befor leaving the factory and no longer likes to drink alcohol. Might be time to try a heated o2s. Where is it? Moot point i suppose as your new cat will have the bung in the converter. Intake setup is stock. Fuel pressure reading is 26psi from filter, that's only place I checked. TPS checks good including idle switch. Throttle stop screw still has its glob of paint in the right spot. Timing 20 deg btdc set with warm engine and green plugs connected. Engine condition is good. Have had heads off on this motor and compression was 135+ on all cyls. I think I have O2 sensor out of the stream and it doesn't respond too well. I was under the impression that the computer ignored the o2s at idle because it knows it's a 1 - wire. But talk to me about a heated sensor! I'm being tested only at idle. If you don't pass at the first time, you get to run it up to 2500 for 15-20 secs and then try again at idle. Link to comment Share on other sites More sharing options...
jono Posted January 25, 2015 Share Posted January 25, 2015 (edited) are "pops out the exhaust" a sign of crappy valve or weak valve spring ? I had a weak valve spring that a machine shop missed when they reassembled it ( oh, yeah, it would have been within spec" he says I say "pigs rrr's" ! There is no within spec on these EA82 - needs to be a figure and that is it. Plicks sent me on a long and expensive wild goose chase - chasing their stuff up Is it a bad combustion that you can hear out the exhaust or is there something in the valve sealing causing this ? A weak valve spring is really noticeable at all temps though, and I found a perfect fresh started engine idle would be screwed as soon as any throttle blip occured, took ages to settle only with engine off, or if drove it to upper revs, change gear - when in next upper gear idle went to crap again Think I have ruled out a weak valve spring for you. On your fuel pressure tested at 26 ...mpfi need about 36 ...did you test it with gauge T'eed in on a running engine? I think you can get inaccurate working pressure readings if you just take pressure at end of line from the pump in an engine off not running situation. My only spfi experience is all non electrical, my spfi is a bit better....like..may I suggest now I think of it - it sort of sounds like an mpfi injector with a crook injector in manifold seat seal - they happen at a hot idle. No good if you are spfi though, and you are. It sounds like it stays with one pot...have you tried blocking off temporarily any vacuum hose ports, plate up the EGR valve on manifold etc ?? Edited January 25, 2015 by jono Link to comment Share on other sites More sharing options...
gdudik Posted January 25, 2015 Author Share Posted January 25, 2015 Thanks! I've really been thinking on the fuel management side of things because my vacuum gauge more or less behaves itself hooked up to that motor. Link to comment Share on other sites More sharing options...
ihscout54 Posted January 25, 2015 Share Posted January 25, 2015 (edited) 26 psi is a bit high ide check to see what you have for pressure in the return line. Edited January 25, 2015 by ihscout54 Link to comment Share on other sites More sharing options...
gdudik Posted January 27, 2015 Author Share Posted January 27, 2015 Ordered a cat. Coming soon. Jono, I have tested the full intake manifold setup with a homemade smoke machine. It occurred to me in the shower that a smoke machine won't show a weak pcv. I'm reasonably sure that the EGR isn't stuck open, but I haven't checked. >>Anybody know how to test to see if the misfire is confined to one cylinder rather than being multiple cyls? I would love a scope but don't have one. It's an intermittent misfire; pulling spark plugs to various cylinders won't tell me anything. Link to comment Share on other sites More sharing options...
Wolfman01 Posted January 27, 2015 Share Posted January 27, 2015 Ok built a good disty out of a couple of old ones, and the idle's much better but not perfect. I even put a gallon and a half of alcohol in it with it on E, and it still won't pass emissions. I've ordered a new cat and Y-pipe, since the old one's an aftermarket anyway and the honeycomb is loose. Also I think where I mounted the O2 sensor is too far out of the stream--it never reports anything over .2 volts, even at 2500 rpm, so I think it's dumping fuel in all the time at cruise. But that doesn't explain my idle misfire. This car is making me tear my hair out. Any ideas? Get the new cats in first, then see what you get. If they're rattling, they are no longer doing their job. How far out of spec are the readings on your test? Link to comment Share on other sites More sharing options...
gdudik Posted January 28, 2015 Author Share Posted January 28, 2015 CO is in spec, less than 1.0. HC limit is 220 , and I'm in the 6-700 range, depending on which test were talking about. NoX does not get tested. They test me at idle only. If I fail on the first idle, I get to run it at 2500 for 20 or so secs and then test again. Numbers are usually a bit lower after run up, but not much. The front cat isn't in pieces inside, but the honeycomb has separated from the housing. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now