Tye Posted July 29, 2015 Share Posted July 29, 2015 (edited) I am currently swapping an ej22 out of a 1992 legacy into my 1990 Loyale. Everything is done except the wiring. i got my harness from SJR, i currently have the 3 yellow wires labeled hot in run and start and hot at all times wired directly to the battery (Just temporarily). the black and red wire labeled fuel pump is wired to the blue and white wire from the old fuel pump relay ( the fuel pump was working but its not anymore) the alternator is wired up to the original wires from the vehicle. (The charge light was flashing while cranking but its not anymore) the wires labeled starter, trans, coolant, fan. radiator, select monitor, oil pressure, ac, check engine, and tach are not currently connected to anything my question is with this current setup is there a way to get it started it currently cranks over fine and the fuel pump was pumping but there is no spark im a little lost at why there is no spark and what happened to the fuel pump i know grounding could be an issue but i don't really know where to start, does the ecu need to be grounded and if so how also i don't know if there is a minimum voltage the battery needs to get everything going it currently has 12.36 volts i have read through several other peoples threads including numbchux, but im running out of things to try, the engine ran fine right before we pulled in out of the donor vehicle i suck at electrical so any help is greatly appreciated thanks Edited July 30, 2015 by Tye Link to comment Share on other sites More sharing options...
Tye Posted July 30, 2015 Author Share Posted July 30, 2015 any ideas? Link to comment Share on other sites More sharing options...
Tye Posted July 30, 2015 Author Share Posted July 30, 2015 anybody? Link to comment Share on other sites More sharing options...
turbosubarubrat Posted July 30, 2015 Share Posted July 30, 2015 You still have the brown relay? On my ej22 swapped hatch there was a small black wire off of it that wasn't hooked up. It didn't have fuel or spark either until it was hooked up. Link to comment Share on other sites More sharing options...
Scott in Bellingham Posted July 30, 2015 Share Posted July 30, 2015 The ground is threw the engine harness, yes you need the brown main relay powered with ignition key Link to comment Share on other sites More sharing options...
Tom0 Posted July 30, 2015 Share Posted July 30, 2015 I think you need to have the wire labled starter hooked up? Shows that the car is cranking/trying to crank. And i dont think the charge light should flash when cranking? Link to comment Share on other sites More sharing options...
Tye Posted August 5, 2015 Author Share Posted August 5, 2015 I think you need to have the wire labled starter hooked up? Shows that the car is cranking/trying to crank. And i dont think the charge light should flash when cranking? The ground is threw the engine harness, yes you need the brown main relay powered with ignition key You still have the brown relay? On my ej22 swapped hatch there was a small black wire off of it that wasn't hooked up. It didn't have fuel or spark either until it was hooked up. thanks for the reply's, where would the starter labeled wire, wire to? Link to comment Share on other sites More sharing options...
Tye Posted August 5, 2015 Author Share Posted August 5, 2015 Is it alright that i cut the wires going to the ea82 through these plugs Link to comment Share on other sites More sharing options...
Prwa101 Posted August 5, 2015 Share Posted August 5, 2015 Its alwasys best to just tuck them up and call it good... now you have exsposed wiring, that runs through out the body... Link to comment Share on other sites More sharing options...
Tye Posted August 5, 2015 Author Share Posted August 5, 2015 Its alwasys best to just tuck them up and call it good... now you have exsposed wiring, that runs through out the body... i pulled the wires out also and cut them off at the yellow plugs that went to the old computer, so there shouldn't be any exposed wires in there. i did this because i didn't think i needed the old computer or any of the wires associated with it. just trying to simplify the old harness as much as i can. just wanted to double check to make sure this was alright and not causing my starting issues. Link to comment Share on other sites More sharing options...
Tye Posted August 7, 2015 Author Share Posted August 7, 2015 The ground is threw the engine harness, yes you need the brown main relay powered with ignition key if i have a manual transmission do the 2 trans wires have to be wired up? if so where? Link to comment Share on other sites More sharing options...
Scott in Bellingham Posted August 8, 2015 Share Posted August 8, 2015 thanks for the reply's, where would the starter labeled wire, wire to? Hooks to wire on the starter, has power only in start mode,disregard trans wires Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now