Bratmobile Posted September 13, 2016 Share Posted September 13, 2016 In my hands-on efforts, and research done thus far @USMB (thank you! great content, but nothing that I can interpret as a sure thing with my limited knowledge) I have a guess as to a likely cause for my 86 Brat not starting. Here's what I can tell you so far: New battery, cables, ignition coil, fusible links. (had a no-spark issue for a while, but that's been fixed) When I chased down the no spark problem I had, I replaced the ignition coil. Once that was done the IGN fuse would blow at every attempted start. My neighbor found a short (photo with the red wire nut, next to the carb) Now with this wire disconnected the fuse does not blow and for a while the car started and ran fine for a few weeks. But eventually it would not start (turns over, but would not run) So now I've determined that the car is not getting fuel at the carburetor, and there is no sound of the fuel pump initial kicking on when I turned on the ignition, (which I could always hear before). In checking the voltage at the fuel pump when turning the key, there is nothing. Also, checking fuses, none are blown. Direct wiring of the fuel pump to the battery and it kicks right on. The two big questions: In my install of the new ignition coil (and the disconnect of the wire by the carb) if I have any wiring incorrect, could that be a cause of voltage not getting to the Fuel pump? And, is there a way to take a meter to the FPCU off of the car and determine whether it's bad? The photo gallery section has the photos as well, with brief descriptions of what is there and what I'm trying to determine. My apologies for the long-windedness. I'm hoping that there are some good explanations to this, as my lack of car knowledge has most likely caused some of my problems. Thanks in advance! Link to comment Share on other sites More sharing options...
skishop69 Posted September 13, 2016 Share Posted September 13, 2016 (edited) That is the float bowl vent solenoid. It should open with the ignition on. If it blows the fuse when connected, it's shorted internally. It has nothing to do with the FPCU. You do need to replace or bypass it or you'll have power issues when cruising under a load. The FPCU only turns the pump on when it gets a signal from the distributor that the engine is indeed running. If it doesn't get that signal, no pumpy. You'll need the schematics to see exactly what does what and test it. I don't have access to mine right now. If memory serves, the negative side of the coil goes to the tach, the FPCU and the ignitor. There are two fused power circuits coming into the FPCU powered buy fuses 14 and 15 IIRC. One circuit out to the fuel pump and one to the choke. Couldn't tell you the colors or pins right now though. Edited September 13, 2016 by skishop69 1 Link to comment Share on other sites More sharing options...
Bratmobile Posted September 14, 2016 Author Share Posted September 14, 2016 Wow~great info for me to get started with. Much appreciated! If it ain't broke you're not trying...is that a Red Green quote? Link to comment Share on other sites More sharing options...
DaveT Posted September 14, 2016 Share Posted September 14, 2016 It could be. .. sounds like a Red Green saying. Link to comment Share on other sites More sharing options...
skishop69 Posted September 14, 2016 Share Posted September 14, 2016 Yes it is! lol Link to comment Share on other sites More sharing options...
DaveT Posted September 14, 2016 Share Posted September 14, 2016 I'm a man. I can change. If I have to... I guess. Link to comment Share on other sites More sharing options...
skishop69 Posted September 15, 2016 Share Posted September 15, 2016 Quando omni flunkus moratati! For those not fluent in Latin, When all else fails, play dead. Literal translation is, When all fails, die. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now