Starlite Posted June 4, 2017 Share Posted June 4, 2017 Is this a bad lifter or might i have a failing bearing? Ea82 mpfi 89. https://youtu.be/QmB5nhxUL64 Link to comment Share on other sites More sharing options...
Starlite Posted June 4, 2017 Author Share Posted June 4, 2017 I have just replaced the headgaskets clean all the lifters ( one had thick tar looking thing in it), reseal oilpump two years ago and resealed the engine. This is the second time i replace headgaskets because of cheap hg last time. This sound could not be heard before hg job. I think. Only a very hard lifter tick. Running 10w30 oil. Link to comment Share on other sites More sharing options...
czny Posted June 4, 2017 Share Posted June 4, 2017 Sure it isn't an exhaust leak? Get a piece of heater hose or garden hose & use it as a stethoscope to listen with. If internal, a long large screwdriver with the handle pressed to your ear helps. Touch the blade to cylinder head, exhaust flange, etc to pinpoint the noise. 1 Link to comment Share on other sites More sharing options...
idosubaru Posted June 4, 2017 Share Posted June 4, 2017 How many miles have you driven since HG replacement? The HLAs are frequently loud after the engine has been apart. There's a place that sells rebuilt HLAs for cheap - like $5 or something, hardly worth guessing with any really nasty or questionable ones. Link to comment Share on other sites More sharing options...
Dee2 Posted June 4, 2017 Share Posted June 4, 2017 Sounds like a mine which I am diagnosing as a lifter tick. noise.mpg Mine was much worse and I did the following which helped reduce the noise significantly. With the dirty oil still in the engine (less 1 qt.), do an engine oil flush. Then change the oil and replace filter. Add new oil with auto, trans. fluid at oil/ATF ratio of 3:1 Run that for about 100 miles and see if the lifter frees up. If there is a significant reduction in noise, you can try a second oil flush at the 100 mile mark when you do the change again. If you don't have any success then you are looking at finding the side with bad lifter noise and replacing the lifters. I found some at RockAuto for $10 ea. I haven't done the replacement yet. Link to comment Share on other sites More sharing options...
superpoo93 Posted June 5, 2017 Share Posted June 5, 2017 Mizpah will rebuild yours. https://mizpahprecision.com/ Link to comment Share on other sites More sharing options...
scoobiedubie Posted June 6, 2017 Share Posted June 6, 2017 You have a lifter tick that is most likely caused when the two oil transfer sealing faces at the interior of the camtower, were not sealed with a little gasket maker, before assembly of the camtower. The gasket maker is very lightly dabbed on around the oil the oil transfer holes, or around the rim of the oil transfer surfaces. There is a secondary whine that sounds like the timing belts are shifted too far backward and rubbing against the plastic back panels. Link to comment Share on other sites More sharing options...
Starlite Posted June 6, 2017 Author Share Posted June 6, 2017 Yes i know about the two surface wich i coated with a thin layer of sealent. The timingbelt want to go against the back panel and i dont know why. I have tryed to turn the belt but it dosent matter. Link to comment Share on other sites More sharing options...
scoobiedubie Posted June 6, 2017 Share Posted June 6, 2017 Yes i know about the two surface wich i coated with a thin layer of sealent. The timingbelt want to go against the back panel and i dont know why. I have tryed to turn the belt but it dosent matter. Then it is probably a bad lifter. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now