ajslacker Posted October 21, 2017 Share Posted October 21, 2017 85 EA81 Brat New Weber Carb New fuel pump Both New fuel filters New ignition coil New battery Brand new Distributor New sparkplugs gapped at .44 New spark plug wires. (Correctly ordered on the cap) New Distributor cap and rotor New PCV valve Timing is correct (checked nine times) New exhaust Did a compression test and it was good. Don't remember the numbers though Still won't start. I don't know why. Any advice or help? Link to comment Share on other sites More sharing options...
Gloyale Posted October 21, 2017 Share Posted October 21, 2017 Firing order 1324 Cyl positions rear 3 4 1 2 Front Check that. And then check for 12v to coil. Check 2 wires to the disty from coil How do you know the timing is correct if you can't get it to run? Link to comment Share on other sites More sharing options...
Dee2 Posted October 21, 2017 Share Posted October 21, 2017 (edited) Is fuel actually getting to the engine ? Getting spark at the plug ? Distributor oriented correctly ? Edited October 21, 2017 by Dee2 Link to comment Share on other sites More sharing options...
bratman2 Posted October 22, 2017 Share Posted October 22, 2017 Pull a plug and check for spark. If you have spark try a oz. or two of fuel in the carb. Link to comment Share on other sites More sharing options...
jono Posted October 22, 2017 Share Posted October 22, 2017 Was it going OK before you treated it to thestable full of goodies? Two things on no start is fuel and spark if it has spark, next trick is to use some form of coaxing, even a tiny dribble of fuel down its throat can make a diference, then there is starter fluid in spray cans...just watch for a backfire when spraying firewater at it! Link to comment Share on other sites More sharing options...
Knucklehead Saloon Posted October 22, 2017 Share Posted October 22, 2017 Distributor leads correct polarity on coil? On mine yellow went to negative. Black went to positive. Link to comment Share on other sites More sharing options...
ajslacker Posted October 22, 2017 Author Share Posted October 22, 2017 It has spark. I checked it by getting someone else to turn it over while I held all the sparks to metal. Im spraying a little carb cleaner into the carb and it doesn't make a difference. ???? Link to comment Share on other sites More sharing options...
jono Posted October 22, 2017 Share Posted October 22, 2017 (edited) you said correctly ordered, but direction correct also? and in correct position? I once thought I just had to have the order and direction correct when I swapped all my six cylinder leads for new. Boy! Was I in for a learning curve that night !!. I think number one lead is the one most closest to the front like in a six of the clock position from viewing usual front of car facing engine. I use the Jono tagging method now, with coloured cable zip ties anything to do with 1 is red, and I recall red is one because same count of letters in the English word spelling anything to do with two is blue, because it rhymes and blue has one more letter than red anything to do with three is green, as three and green both have double ee, and green has one more letter than "blue" anything to, whoops ! do with four is yellow, as one more letter in yellow than green if you have any more cylinders work out your own sequence with black and white zip ties OK ?? I have also extended this colour theme to my tools 8mm spanners and T wrenches get black 10mm get red 12mm get blue 14mm get green 17mm get yellow 19mm get recycled - black as if I canna tel the difference between 8mm and 17mm stuff I better give up!! I am slowly going through my drill driver bits as well so any 8mm hex driver for sheet screws etc get gloss black all over, ten mm red paint, 12mm blue paint all over. Just requires finding, cleaning up with solvent, find a can colour, hit 'em, let the paint dry and harden and return back to where they should belong. As I find more not painted they get ID check first, then the treatment. Other odd sizes dont get no paint. Just far easir picking the correct tool when required. I cant make any money out of my system so may as well put it up out there under freeware licence agreement So, I tag both ends of HT leads when I know it is correct and working, but shoot it is hard to get that 1342 ingrained out of my head !! Yep, so spark has to occur at the correct time too, if you got the timing, position wrng you will still get spark just she wont fire!! Edited October 22, 2017 by jono 2 Link to comment Share on other sites More sharing options...
ajslacker Posted October 22, 2017 Author Share Posted October 22, 2017 Well it started for a few seconds when i put gas straight into the carb. Both fuel filters and the fuel pump are all new what would cause it to not get fuel? Link to comment Share on other sites More sharing options...
ajslacker Posted October 22, 2017 Author Share Posted October 22, 2017 Update. Now i dont even need to put fuel in the carb. Itll start up after 2 crabks and itll idle for 5 to 15 seconds then it backfires and dies. Link to comment Share on other sites More sharing options...
Dee2 Posted October 23, 2017 Share Posted October 23, 2017 backfiring can be an indicator of a timing problem. Link to comment Share on other sites More sharing options...
wagons Posted October 23, 2017 Share Posted October 23, 2017 I'm with dee2. I had #1 spark plug wire hooked up at #2 and vice versa. It started, Ran and then died. After looking at my trusty (untrusty) Haynes book I realized plug one was front passenger bank, and number 2 was front driver plug. Simple fix. Also be sure you set ignition timing between 14-20°. Factory is 8 weber carbed subies like 14-20 depending on elevation. Remember when setting ignition timing the vacuum lead to the distributor must be unhooked. Also make sure you put fresh gas in. Good luck and let us know! Link to comment Share on other sites More sharing options...
Knucklehead Saloon Posted October 23, 2017 Share Posted October 23, 2017 Firing order is anticlockwise looking at top of dizzy cap. If its a fuel starvation problem then try blowing out the fuel lines from the carb to the tank (after you disconnect them) with compressed air. Sometimes the lines clag up after yrs of use. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now