steve56 Posted September 22, 2018 Share Posted September 22, 2018 What is the proper procedure of installing cam seals on ej25. Does the cam shaft snout and the inside of seal get lubricated before seal is installed, or is it a dry fit between snout and cam seal. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 22, 2018 Share Posted September 22, 2018 Lube the ID of the seal. Dow 111 is my preferred lubricant. If you really want to make sure the seal never walks out, run loctite 268 around the OD before you put it in. The next guy will hate you though. GD Link to comment Share on other sites More sharing options...
nvu Posted September 22, 2018 Share Posted September 22, 2018 (edited) Grease or oil up the inside where it meets the shaft. Lightly grease or oil the outside so it doesn't pinch while going in. I prefer pressing as hard as possible by hand until it's centered, tap until flush with the head. I had an older ej22 head with a chamfered hole on the driver side. In this case, using the old seal flipped around would allow me to push the new seal further in. Don't bottom it out, the goal is to push the seal in just enough so the outer area makes full contact in the metal hole and holds tight. Oh the snout with the oring, silicone grease or oil is ok. Edited September 22, 2018 by nvu Link to comment Share on other sites More sharing options...
steve56 Posted September 22, 2018 Author Share Posted September 22, 2018 16 minutes ago, GeneralDisorder said: Lube the ID of the seal. Dow 111 is my preferred lubricant. If you really want to make sure the seal never walks out, run loctite 268 around the OD before you put it in. The next guy will hate you though. GD Will Permatex Ultra Slick assembly lube or motor oil work instead of Dow 111. Don't have any Dow 111 on hand. 1 Link to comment Share on other sites More sharing options...
montana tom Posted September 22, 2018 Share Posted September 22, 2018 Either will work fine. I usually swab a finger thru some white lube and give a wipe on the id and the snout. Using loctite on the od is a good idea, iv'e had them come in the shop with a cam seal popped out. Link to comment Share on other sites More sharing options...
steve56 Posted September 22, 2018 Author Share Posted September 22, 2018 What kind of white lube. I have WD 40 water resistant silicone lubricant and WD 40 protective white lithium grease. Link to comment Share on other sites More sharing options...
steve56 Posted September 23, 2018 Author Share Posted September 23, 2018 5 hours ago, montana tom said: Either will work fine. I usually swab a finger thru some white lube and give a wipe on the id and the snout. Using loctite on the od is a good idea, iv'e had them come in the shop with a cam seal popped out. What kind of white lube are you using. Don't see any white lube at nappa. Link to comment Share on other sites More sharing options...
montana tom Posted September 23, 2018 Share Posted September 23, 2018 What I'm using is lubriplate, but any assembly lube or just plain oil will work. The idea is to lube it up the first time after that the engine oil takes care of it. Use what you got . Just don't push that seal all the way in. Link to comment Share on other sites More sharing options...
steve56 Posted September 23, 2018 Author Share Posted September 23, 2018 Ok thanks for clarifying that. I'm redoing the cam seals due to a slow drip of oil on drivers side cam seal. I had put oil on just the bottom quarter of the seal. Looks like going all the way around ID of seal is better. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 23, 2018 Share Posted September 23, 2018 (edited) Lubriplate assembly lube is what I use on rods, mains, and cams. Any journals. Would work for the seals also. The Dow 111 really protects the seals and especially o-rings. Coating the nitrile rubber o-rings in 111 keeps oxygen from getting to the rubber and that's really what is responsible for making them hard and crack. Oxygen and heat. 111 is amazing stuff to have on hand in any garage. Besides lubricating any and all seals, oil filter gaskets, etc - it is also a perfect dielectric grease for all electrical connections including plugs and wires. Don't lubricate the OD of the seal. It can and will pop back out. Using the loctite 248 stick will provide for smooth installation and quickly cure making it almost impossible for the seal to come back out on it's own. Indeed - quite a lot of force and red hot cursing will be involved in its removal. GD Edited September 23, 2018 by GeneralDisorder 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now