smartin Posted January 12, 2020 Share Posted January 12, 2020 The hood isn't releasing when I pull the lever. How do I release the hood manually. Thanks Link to comment Share on other sites More sharing options...
lmdew Posted January 13, 2020 Share Posted January 13, 2020 I'd fist check and see if the cable is on the lever attached inside the car. If so, have someone push down on the hood when you pull the lever and then pull up the hood. If the cable ball end is not attached to the lever under the dash, you could just pull it with a vice grips. If neither of those work you will have to get into the grill area to pull on the cable or unbolt the latch 12mm bolts. Link to comment Share on other sites More sharing options...
gbhrps Posted January 13, 2020 Share Posted January 13, 2020 smartin, What will work for one person's situation on this issue, may not work for another. I've been where you're at more than once and I can tell you that it often requires a lot of different techniques. Sometimes you can get the front grill out and get a hold on the hood unlock cable and pull it. Sometimes spraying the daylights out of the latch assembly through a grill opening with WD40, waiting a while and then pushing down on the front of the hood while someone pulls hard on the cable from inside the car will do the trick. Sometimes you can get at the latch assembly from underneath the car and unbolt it, or if its visible from through the grill unbolt the latch assembly and raise the hood enough to be able to pry the moving parts to release. A last resort may be to use a hacksaw blade held by its end in vice grips to cut through the latch and then replace parts from a wrecking yard. Basically you're going to have to get inventive, short of destroying the hood to get it open. Good Luck! Link to comment Share on other sites More sharing options...
smartin Posted January 13, 2020 Author Share Posted January 13, 2020 I haven't had time to get into it yet but it looks tricky. If the problem is at the pull lever it will be easy if it is any where else ouch. If you look at the picture this is a hood latch from a 2006 outback I am willing to bet they are basically the same. The problem is the cable protector on the right side. It prevents reaching in through the grill and just pulling the cable outback hood latch _.html Link to comment Share on other sites More sharing options...
smartin Posted January 13, 2020 Author Share Posted January 13, 2020 Link to comment Share on other sites More sharing options...
lmdew Posted January 13, 2020 Share Posted January 13, 2020 The cable runs under the radiator support from the drivers side. Could pull front wheel and inner fender and you'd see it. Last resort. Link to comment Share on other sites More sharing options...
smartin Posted January 13, 2020 Author Share Posted January 13, 2020 Inner fender sounds ugly. Do you think the latch bolts can be removed through the grill? Link to comment Share on other sites More sharing options...
heartless Posted January 13, 2020 Share Posted January 13, 2020 if you can get a socket up in there & access thru the grill, it doesn't hurt to try. I feel for ya, either way. Mine is the opposite, tho - have a hard time getting it to latch properly sometimes.. have to spray it down good and manually work the latch a few times when it starts acting up Link to comment Share on other sites More sharing options...
lmdew Posted January 14, 2020 Share Posted January 14, 2020 What did you find at the latch tab inside the car under the dash? Shoot a pic. Link to comment Share on other sites More sharing options...
smartin Posted January 14, 2020 Author Share Posted January 14, 2020 I won't have time to really get to it until sat. Not urgent yet. Thanks hoping it's a latch tab issue thanks. Link to comment Share on other sites More sharing options...
smartin Posted March 12, 2020 Author Share Posted March 12, 2020 Sorry this update took so long. When I finally got to it I had some one hold the latch release up while I played with the hood. Had to actually pry up slightly with a screw driver but it popped up. All gunked up and just stuck. cleaned lubed now seems to be working fine.Thanks to every one that commented. if that cable had broken or come unhooked this would have been a night mare. 1 Link to comment Share on other sites More sharing options...
lmdew Posted March 13, 2020 Share Posted March 13, 2020 Glad you got it! Link to comment Share on other sites More sharing options...
heartless Posted March 13, 2020 Share Posted March 13, 2020 glad you got it sorted out. mine will periodically gunk up as well - i live on a gravel road, so lots of dust - but i usually have the opposite problem - it wont close properly! Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now