3Pin Posted August 28, 2020 Share Posted August 28, 2020 Just bought a 2000 Subaru outback with a bad manual trans. Car-part tells me 2000 is the only match. Surprised a 2001 or 2002 wouldn't swap in? Anyone know? Link to comment Share on other sites More sharing options...
GeneralDisorder Posted August 28, 2020 Share Posted August 28, 2020 You can swap any year you like up to 2004 as long as you use the matching rear diff or the trans matches what you have. With 2005+ you also need to swap the front axles. Don't go beyond about 2007 though or you may find there is no way to install the speed sensor in the front diff. There's ways around that also if necessary but it involves some electronics to create a VSS signal from the ABS wheel speed sensor...... 99's are the same also. And you can use older transmissions as well. They just have a different transfer case housing and such. But they will interchange as long as you have a matching ratio rear diff. If you use a 90 to 98 trans it will have a 4 bolt bell-housing so 4 of the bolts will not be used. GD Link to comment Share on other sites More sharing options...
3Pin Posted August 28, 2020 Author Share Posted August 28, 2020 so a 2001 or 2002 from another outback will have the same gear ratio and will work correct. I want to to try to swap in the replacement trans only if possible. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted August 29, 2020 Share Posted August 29, 2020 Yeah I think all the Outbacks from that vintage had 4.11 final drives. Go on parts.subaru.com and cross reference the part number for the rear differential. Anything that matches will have the same trans. GD Link to comment Share on other sites More sharing options...
3Pin Posted August 31, 2020 Author Share Posted August 31, 2020 Thanks GD. Link to comment Share on other sites More sharing options...
3Pin Posted August 31, 2020 Author Share Posted August 31, 2020 All-Wheel-Drive 5-speed TransmissionsUSDM3.454 / 1.947 / 1.366 / 0.972 / 0.738 / 3.900FD - '02-'05 USDM WRX3.454 / 1.947 / 1.366 / 0.972 / 0.738 / 3.700FD - '06-'07 USDM WRX3.166 / 1.882 / 1.296 / 0.972 / 0.738 / 3.900FD - '08-current USDM WRX3.454 / 1.947 / 1.366 / 0.972 / 0.738 / 4.444FD - '04-'08 Forester 2.5XT3.454 / 2.062 / 1.448 / 1.088 / 0.780 / 4.111FD - '04-current Forester non-turbo3.166 / 1.882 / 1.296 / 0.972 / 0.738 / 4.111FD - '05-'06 USDM Legacy 2.5GT3.166 / 1.882 / 1.296 / 0.972 / 0.738 / 3.900FD - '07-'09 USDM Legacy 2.5GT3.166 / 1.882 / 1.296 / 0.972 / 0.738 / 4.444FD - '05-'09 USDM Outback 2.5XT3.545 / 2.111 / 1.448 / 1.088 / 0.780 / 4.111FD - '98-'01 USDM Impreza 2.5RS3.545 / 2.111 / 1.448 / 1.088 / 0.780 / 3.900FD - '96-'01 USDM Impreza L/OBS3.545 / 2.111 / 1.448 / 1.088 / 0.780 / 4.111FD - '96-'99 USDM Legacy 2.5GT3.545 / 2.111 / 1.448 / 1.088 / 0.871 / 4.111FD - '96-'99 USDM Legacy Outback3.454 / 2.062 / 1.448 / 1.088 / 0.871 / 4.111FD - '00-'07 USDM Outback3.454 / 2.062 / 1.448 / 1.088 / 0.825 / 4.111FD - '08-current USDM Outback3.454 / 2.062 / 1.448 / 1.088 / 0.780 / 4.111FD - '02-'04 USDM Impreza 2.5RS/'05 Impreza 2.5RS Sport3.545 / 1.947 / 1.366 / 0.972 / 0.780 / 4.111FD - '93-'94 USDM Impreza 1.8L3.545 / 2.111 / 1.448 / 1.088 / 0.825 / 3.900FD - '95 USDM Impreza 1.8L Link to comment Share on other sites More sharing options...
el_freddo Posted September 1, 2020 Share Posted September 1, 2020 Get the front drive shafts too. At some point in the Gen3s (or was it the foresters, I can’t remember now!) they went from diff stub axle with cotter pin to hold drive shaft on to drive shaft pushed into diff held by a C clip on the driveshaft. This changes the bearing tensioner setup and the oil seal as a result of this change. Having the matching driveshafts come with the gearbox ensures you have what you need to drop in and go. Cheers Bennie 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now