sirtokesalot Posted December 20, 2021 Share Posted December 20, 2021 i have a friend with the 2004 outback h4 cali emissions and has the exhaust that looks exactly like an h6 exhaust. 3 cats and 5 sensors single oval ports on the heads. is the h6 exhaust the same thing or is there something different about it that it wont fit? the h6 cats can be found cheaper than the ones that say there for the h4 specifically. Link to comment Share on other sites More sharing options...
montana tom Posted December 24, 2021 Share Posted December 24, 2021 2004 cars issued to California had round port heads and drive by wire throttle. 2004 cars sold to the rest of the country are the same as 2003. Link to comment Share on other sites More sharing options...
laegion Posted December 25, 2021 Share Posted December 25, 2021 On 12/20/2021 at 8:11 AM, sirtokesalot said: i have a friend with the 2004 outback h4 cali emissions and has the exhaust that looks exactly like an h6 exhaust. 3 cats and 5 sensors single oval ports on the heads. is the h6 exhaust the same thing or is there something different about it that it wont fit? the h6 cats can be found cheaper than the ones that say there for the h4 specifically. No. It's not the same. The exhaust gaskets for the manifold to pipe is not the same part as for the H6. The muffler is also different if I'm not mistaken. Link to comment Share on other sites More sharing options...
sirtokesalot Posted December 26, 2021 Author Share Posted December 26, 2021 21 hours ago, laegion said: No. It's not the same. The exhaust gaskets for the manifold to pipe is not the same part as for the H6. The muffler is also different if I'm not mistaken. i was hoping to use the cat section of an h6 and keep the h4 rear section. this is one of the cat sections i hollowed out to get his car running again for now. you can see the port for where it mounts up tot eh engine in this picture. this is the exhaust i took off the 2004 h4 outback that i want to replace with the h6 version. are we sure its not the same? Link to comment Share on other sites More sharing options...
heartless Posted December 26, 2021 Share Posted December 26, 2021 Opposed Forces shows basically the same images for the 6 and the 4 for MY04 - images for MY05 the H6 has a very different manifold - 3 individual ports vs a single oval I kinda think the only way to know for sure would be to get your hands (or eyes at a junkyard maybe?) on a used H6 exhaust and physically match it up - verify measurements, etc Link to comment Share on other sites More sharing options...
idosubaru Posted December 26, 2021 Share Posted December 26, 2021 I have a complete H6 exhaust on my garage floor, I’m not home to go look but that looks very much like it. I could pull a measurement if needed or check sensor locations Just check the gasket part numbers, if they’re the same then the form factors are as well and then you just need to ensure the oxygen sensor(s?) are there and in the right spot. Link to comment Share on other sites More sharing options...
laegion Posted December 27, 2021 Share Posted December 27, 2021 5 hours ago, idosubaru said: I have a complete H6 exhaust on my garage floor, I’m not home to go look but that looks very much like it. I could pull a measurement if needed or check sensor locations Just check the gasket part numbers, if they’re the same then the form factors are as well and then you just need to ensure the oxygen sensor(s?) are there and in the right spot. The gasket part numbers are not the same. Link to comment Share on other sites More sharing options...
laegion Posted December 27, 2021 Share Posted December 27, 2021 https://www.discountedsubaruparts.com/p/Subaru_2004_Legacy-25L-AT-4WD-Outback-Wagon/Exhaust-Pipe-to-Manifold-Gasket-Front-Exhaust-Pipe-to-Manifold-Gasket/49250540/44011AE050.html 3.0 is not listed in "what this fits" and alternatively no 4cyl listed on the "what this fits" for the ez30 gasket. Link to comment Share on other sites More sharing options...
idosubaru Posted December 27, 2021 Share Posted December 27, 2021 17 hours ago, laegion said: https://www.discountedsubaruparts.com/p/Subaru_2004_Legacy-25L-AT-4WD-Outback-Wagon/Exhaust-Pipe-to-Manifold-Gasket-Front-Exhaust-Pipe-to-Manifold-Gasket/49250540/44011AE050.html 3.0 is not listed in "what this fits" and alternatively no 4cyl listed on the "what this fits" for the ez30 gasket. The exhaust wouldn’t mean much. Infinite Subaru parts interchange even if they’re not cross listed and have a separate part number. Different gaskets might suggest different bolt spacing or pipe diameter though. There isn’t much else to them to vary aftermarket sometimes lists gasket dimensions you could possibly compare why they differ. Link to comment Share on other sites More sharing options...
idosubaru Posted December 27, 2021 Share Posted December 27, 2021 I’ll measure H6 diameter if I remember next time I’m in the garage. Link to comment Share on other sites More sharing options...
laegion Posted December 28, 2021 Share Posted December 28, 2021 17 hours ago, idosubaru said: The exhaust wouldn’t mean much. Infinite Subaru parts interchange even if they’re not cross listed and have a separate part number. Different gaskets might suggest different bolt spacing or pipe diameter though. There isn’t much else to them to vary aftermarket sometimes lists gasket dimensions you could possibly compare why they differ. From what I read, one of the studs doesn't line up with the ez30 gasket. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now