Scotty Posted August 25, 2004 Share Posted August 25, 2004 first of all, I wish I found this forum a year ago!. but now maybe you fine folk can help me sort out a problem. 1999 Forester L, manual trans, after it's warmed up and driving for a while (10 plus miles) it does a "thump thump thump" as well as a "grabbing" thing on the sterring strong enought to bounce the car a bit when going around tight corners, moreso to the left than right. so far I have been told CV Joint. Transmission Limited Slip Diff Viscous Coupling damedifIknow money is tight, already had some fancy fluid added to the diff, no good there. any ideas on which way to go to deal with this problem? I can't afford to pick more than one option. Scotty Link to comment Share on other sites More sharing options...
Guest lothar34 Posted August 25, 2004 Share Posted August 25, 2004 Did you have the wheel bearings checked? Link to comment Share on other sites More sharing options...
MorganM Posted August 25, 2004 Share Posted August 25, 2004 Thats kinda scary if you can feel it at the steering wheel when it happens. Makes me think something is VERY loose. Budget is tight? TIme to Do It Yourself Jack up the car on the side that you feel/hear the noise. Pull off that wheel and take a good look! Grab onto things and give them a good yank. Look for stuff thats loose or obviously broken. Look for grease flung all over and try to locate its origine. Look down below at your ball joints. This is where the lower control arm meets the knuckle below your brake rotor. After you put the wheel back on but before you lower the car; grab the wheel and try to wiggle it. It should be tight and not able to wiggle to/from you. By atleast looking you might find it and then you can TELL the shop what you want done. Then you can call around and get estimates on the job you know that needs done. Link to comment Share on other sites More sharing options...
sasquatch Posted August 25, 2004 Share Posted August 25, 2004 stop driving it until it is checked....it sounds like you may well have a front axle problem.... Link to comment Share on other sites More sharing options...
Ranger83 Posted August 25, 2004 Share Posted August 25, 2004 You don't mention the mileage but you can lose a wheel bearing in as little as 60K. Drive train problems are not impossible, but rare. If you go to a parking lot and do slow figure 8's, the clunk will speed up or slow down on one side if it's and axle, CV joint, or bearing. If it's an axle or CV joint, you should hear a metallic click or some sort of noise when stationary and you shift back and forth between 1st and Reverse. If you don't hear anything while stationary, it's more likely to be a wheel bearing. If you don't have it repaired quickly you will trash the brake rotor on that side, and will wind up replacing the front rotors and brake pads along with the wheel bearing. If it's grabbing to one side either the bearing is really far gone or you more likely have some other front suspension problems. Neglecting it will multiply your repair bill. Link to comment Share on other sites More sharing options...
Guest lothar34 Posted August 26, 2004 Share Posted August 26, 2004 Also, if it is a bearing, there were some Forester MYs where people have been replacing the stock bearings with the ones from the Legacy of that MY. It's a different type of bearing, but a direct swap and a much better deal. Link to comment Share on other sites More sharing options...
subiemech85 Posted August 26, 2004 Share Posted August 26, 2004 http://www.ultimatesubaru.org/forum/showthread.php?t=11848 for a how2 I am guessing from personal experience that you have a broken outer "cage" on the left side, and are possibly missing a ball requiring you to replace the left side axle shaft If you don't have the $80+ for a rebuilt unit, then you can just pull the stub shaft from the main shaft and use RWD Link to comment Share on other sites More sharing options...
urabus1995 Posted August 26, 2004 Share Posted August 26, 2004 I had the same problem on my old DL 1.8 Wagon.It was the Cv joint gone bad, due to lack of grease( split boot). Repair was not too expensive, using a second hand part. I dont know what a new one would cost, but being Subaru I think it may be quite a lot of dosh. As others have mentioned, if you jack up the car and try to wiggle the wheel , you will hear the clunk and see the CV move in a strange fashion. This movement should be checked horuzontally. If you get wheel movenent shaking perpindiculary, then its a wheel bearing/hub gone bad. Wheel bearings normally "hum" when going bad , rather than "clunk". Link to comment Share on other sites More sharing options...
ptrbilt Posted August 26, 2004 Share Posted August 26, 2004 This sure sounds like the rear differetial on the tranny is shot. You drive 10 miles and the clutch pack heat up and then won't release going around a turn. Wheel bearings won't clunk they hum (as posted earlier) when they get load goiung around a bend at speed. A bad CV joint won't take ten miles to "thunk" Try removing the rear drive shaft. Not sure how the forester is set up but if it is like the Outback then just remove the rear half of the shaft. The front half will hang from the carrier bearing and stay out of the way. Once the front and rear wheels are seperated you should notice the binding going around bends. If this isn't the problem then you can reinstall the drive shaft and keep looking. Hope this helps, Peter Link to comment Share on other sites More sharing options...
friendly_jacek Posted August 29, 2004 Share Posted August 29, 2004 first of all, I wish I found this forum a year ago!. but now maybe you fine folk can help me sort out a problem. 1999 Forester L, manual trans, after it's warmed up and driving for a while (10 plus miles) it does a "thump thump thump" as well as a "grabbing" thing on the sterring strong enought to bounce the car a bit when going around tight corners, moreso to the left than right. so far I have been told CV Joint. Transmission Limited Slip Diff Viscous Coupling damedifIknow money is tight, already had some fancy fluid added to the diff, no good there. any ideas on which way to go to deal with this problem? I can't afford to pick more than one option. Scotty Sounds like binding indeed. Are your tires exactly same size?Any follow-up? Link to comment Share on other sites More sharing options...
Scotty Posted August 30, 2004 Author Share Posted August 30, 2004 wow! thanks for all the replies guys! sorry I haven't been back but the computer decided crap out as well. ok, lets see. in order. I THINK I've had the wheel berings checked (it's been looked at by 4 differnt mechanics), but I will double check that. Morgan: it seems to be pretty much even now, slightly more on the left side I think (my wife thinks it's more on the right side) millage is in the mid 90's I'll try the figure 8 thing Ranger., thanks there is a VERY clear "click" when stationary and shifting from first to reverse, just as it's hitting or comeing out of reverse. Urabus: they have pulled off all 4 wheels, rotated them, did the wiggle thing. all seemed solid. the dealer seems to be leaning twards replaceing the Viscus coupling. $800-$1000 bucks. (so far they have "fixed" my breaks three times and they still squeel and the car had $1200.00 worth of repairs within 30 days of me buying it, I DON'T trust the dealer) I had the tires checked, all same size. I'll try that figure 8 thing, and see about getting the rear end diconected ptrbilt thanks much guys, now at least I have some ideas. Scotty Link to comment Share on other sites More sharing options...
Ranger83 Posted August 30, 2004 Share Posted August 30, 2004 there is a VERY clear "click" when stationary and shifting from first to reverse, just as it's hitting or comeing out of reverse. I'd get a second opinion, as that sounds like an axle. Just had one replaced, total was about $210. Link to comment Share on other sites More sharing options...
Scotty Posted August 31, 2004 Author Share Posted August 31, 2004 I'd get a second opinion, as that sounds like an axle. Just had one replaced, total was about $210. front or rear Ranger? and that I amount I can deal with. as long as I don't have to do the "well, we thought it was the viscus coupling, but we replaced that at $900.00 and it still does it, lets try this other $800.00 thing" routine.. and I did the figure 8 thing, more left than right. I'll bounce your ideas off the one mechanic I trust on this, thanks again guys, I'll keep you updated. Link to comment Share on other sites More sharing options...
MorganM Posted August 31, 2004 Share Posted August 31, 2004 Sounds mostly like it could be the inner DOJs on the axle assemblies. If you look at your axle from tire/hub to tranny its kinda like this -<>===[ ]= The - stub axle on the left end there, then the <> CV joint on the outside end, then the ==== axle shaft itself and finally [ ] the DOJ that goes onto the = splined stubs on the tranny. Usually the outer CVs go first cuz they take more abuse; having to turn, articulate and still rotate at the same time. Inner DOJs can wear out also tho and make a similar 'click' or 'pop' when shifting gears or taking off especially. Id get the axles checked out before coind the V.coupler! That thing is expensive 0_0 Good luck Link to comment Share on other sites More sharing options...
Scotty Posted September 1, 2004 Author Share Posted September 1, 2004 just came from my mechanic, seems he asked around and 4 or 5 other Forester owners are haveing the same problem. Viscous Coupling, $900.00. anyone want to buy a 1999 Forester? Link to comment Share on other sites More sharing options...
ptrbilt Posted September 2, 2004 Share Posted September 2, 2004 just came from my mechanic, seems he asked around and 4 or 5 other Forester owners are haveing the same problem. Viscous Coupling, $900.00. anyone want to buy a 1999 Forester? Just remove the rear drive shaft and you've got a fully functional FWD Forester. A junk yard center differential should only cost you $200-$300. Good Luck, Peter Link to comment Share on other sites More sharing options...
unibrook Posted June 12, 2013 Share Posted June 12, 2013 Years late for your car, but the key clue is that the binding only happens when the car is WARM. Therefore it is a fluid problem. First try at a fix: Replace your front differential fluid. I used 3.5 quarts of Lucas Synthetic gear oil. That worked on my 2001 Forester with manual transmission. 2 years ago, and no problems since. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now