broken Posted August 30, 2004 Share Posted August 30, 2004 hello everyone ! I'm hoping that someone could help me. I was givin 2 subaru's, an 88 gl fuel inj. and a 85 carb. both have 1800's in them I was driving the 88 till the engine quit, so I tried the 85, but it was having major carb trouble. I found alot of gas mixed in the oil, so I decided to try the 85 in the 88 car with the fuel inj. After the switch the engine started right up. It ran about a minute and started to smoke oil smoke alot. It will start immediatly, and it runs strong, but after a minute just starts to smoke alittle, and slowly gets to fog up the whole area. The engine has not run for a year, and didn't smoke the last time it ran. I put oil in each cylider and turned the engine by hand before startin it. There is a ticking sound on one side of the engine. Link to comment Share on other sites More sharing options...
beauregaardhooligan Posted August 30, 2004 Share Posted August 30, 2004 Welcome to the board! It's not at all unusual for an engine that has been sitting to smoke after being started. Just clearing it's throat. Take it easy on it and see how it does. Link to comment Share on other sites More sharing options...
broken Posted September 1, 2004 Author Share Posted September 1, 2004 After a few days of running the car a little at time it's not ticking anymore. It stopped burning oil clouds, but it still smokes alot and water is coming out the exhaust pipe, which I'm guessing it was doing all along, but didn't notice becuase of the oil smell, and smoke. I checked the compression, and it was 125 in all cyinders. It runs great, starts fast, but after it runs to operating temp it will smoke so much I could hide the empir state building in about 2 minutes. Anyone have any ideas what I should check? Link to comment Share on other sites More sharing options...
bajavwnsoobnut Posted September 1, 2004 Share Posted September 1, 2004 look for airbubbles in the coolant and also smoke coming out of there too Link to comment Share on other sites More sharing options...
beauregaardhooligan Posted September 1, 2004 Share Posted September 1, 2004 Yeah, sounds like a bad head gasket or possibly cracked head leaking coolant into the cylinder. I'll bet a lot of that smoke is water vapor. Does the radiator lose water? Link to comment Share on other sites More sharing options...
Hondasucks Posted September 2, 2004 Share Posted September 2, 2004 Check the PCV valve, if it is bad it will make it burn oil and it's like a $2 part. So you put the fuel injected motor in the 85, did you swap the fuel injection, or did you put the carb stuff on the fuel injected motor? If that is what you did, did you use sealant on the manifold gaskets, and the carb gasket (if you took the carb off) because if you didnt' seal it properly it will suck water and make it smoke. The fact you have decent compression in all four cylinders, and it's teh SAME in all four cylinders, leads me to beleive it's not a head gasket. Link to comment Share on other sites More sharing options...
broken Posted September 2, 2004 Author Share Posted September 2, 2004 I replaced the pcv after reading a thread from this site, but still smokes. Just to get this correct, I put the 85 carb engine in the 88 fuel inj car and put the fuel inj on the carb engine. when putting the intake on it said not to use casket sealant, you think maybe that the intake manifold could be leaking? Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 2, 2004 Share Posted September 2, 2004 Intake manifold gaskets. Get the from the dealer, or Fel-Pro only. I've had very bad luck with aftermarket manifold gakets. Use gaskachinch on them - basically it's contact cement. GD Link to comment Share on other sites More sharing options...
broken Posted September 2, 2004 Author Share Posted September 2, 2004 Thanks for the suggestion, I'll try the dealer for the gaskets. I never heard of gaskachinch. Is it like that blue rubbery make a gasket stuff? Link to comment Share on other sites More sharing options...
exister99 Posted September 2, 2004 Share Posted September 2, 2004 I would torque down the cylinder heads first. There is a thread on this site somewhere with instructions for making the special tool for nut #1. According to some this should be done every 12K miles, though I suspect most Soobs haven't had it done since the factory. Link to comment Share on other sites More sharing options...
able41 Posted October 1, 2004 Share Posted October 1, 2004 I need help and could not figure out how to start a new post with my ???? . I have a Subaru WRX 2.0 engine 2002 year and i need the cylinder head tork specks to block???. can you help me please. Thank you able41 Link to comment Share on other sites More sharing options...
Guest taprackready Posted October 1, 2004 Share Posted October 1, 2004 Thanks for the suggestion, I'll try the dealer for the gaskets. I never heard of gaskachinch. Is it like that blue rubbery make a gasket stuff? No, Gaskachinch is not like the BLUE RUBBERY STUFF. Intake gaskets should be put on dry or use an adhesive which makes the gasket stick to the intake so while your putting it on it won't slip and slide around. I've only removed and replaced 2 EA81 intakes and both times I used the least expensive paper intake gasket I could find. Have not have any leaks. Make sure to use anti-seize on the intake bolts and torque them to spec. Bill Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now