lmdew Posted March 16, 2006 Share Posted March 16, 2006 Most shops will never notice and it will pass all emissions and OBDII tests. If the tester questions you just go to the next one. Link to comment Share on other sites More sharing options...
YetiMan Posted March 17, 2006 Share Posted March 17, 2006 well...bought the 1995 EJ22 (impreza automatic w/EGR) dropped it and the OBW off at shop. I'd really hoped to get some photos and write this up and maybe learn something myself but my friend was uncomfortable with that, so I'm just crossing my fingers at this stage and hoping it all goes well. Link to comment Share on other sites More sharing options...
Wayne Boncyk Posted March 17, 2006 Share Posted March 17, 2006 Good Luck, Man! I hope the swap goes without major incident. Let us know if anyone in the Utah Air Quality Gestapo descends down on you!! Link to comment Share on other sites More sharing options...
cookie Posted March 17, 2006 Share Posted March 17, 2006 This is a man with the courage to fight the system! Link to comment Share on other sites More sharing options...
YetiMan Posted March 18, 2006 Share Posted March 18, 2006 update: the engine dropped in and ran with no hassles. need exhaust gaskets to finish up on monday. It was a pleasant surprise to find out the CV boots are torn on both sides. all the info on this board was correct and really, really helped get this done. :clap: :clap: :clap: Link to comment Share on other sites More sharing options...
Wayne Boncyk Posted March 18, 2006 Share Posted March 18, 2006 Congrats! Link to comment Share on other sites More sharing options...
3Pin Posted March 25, 2006 Share Posted March 25, 2006 Congrats. Excellent information here Kevin in post 18 talked about a custom bracket that needed to be built. Does anyone know what he is referring to? I am going to take the plunge with one of these shortly. Link to comment Share on other sites More sharing options...
tbreaden Posted February 18, 2008 Share Posted February 18, 2008 New to forum But can you tell me if this plug in EJ22 swap will work in a 1999 Forrester. Thanks Todd Link to comment Share on other sites More sharing options...
Durania Posted February 18, 2008 Share Posted February 18, 2008 Probably would have been better to just start a new thread and describe your problem instead of digging another one up. Other than that, welcome to the board. Link to comment Share on other sites More sharing options...
Bigbusa Posted February 18, 2008 Share Posted February 18, 2008 Engine was $2105.00 (including shipping)Installation was $600.00 (including extra parts, fluids, etc) Total: $2700.00 (and now has a 3 year warranty on the engine!!) Can you imagine less than 4 years later CCR is now charging $3570 for a rebuilt 2.2L?!!! That's absolutely rediculous. They charge a $375 core charge too. People are swapping a 2.5L for a 2.2L. Why charge a core charge on a completely different engine? Maybe they know this and will only accept a 2.2L engine as the core? Who in their right mind is going to go through the trouble of palletizing their 2.5L engine, taking it to a shipper, paying $100 or more for shipping to colorado and then hoping they refund the $375??? IMO, CCR is a very poor option now. Link to comment Share on other sites More sharing options...
msmithmmx Posted February 18, 2008 Share Posted February 18, 2008 Is this for real , "CCR is now charging $3570". Thats a rip off. Who would pay that??? Link to comment Share on other sites More sharing options...
porcupine73 Posted February 18, 2008 Share Posted February 18, 2008 Yes curious where that price came from? A CCR 2.2L sold on eBay for like half that in September. Link to comment Share on other sites More sharing options...
Bigbusa Posted February 18, 2008 Share Posted February 18, 2008 Out of curiosity, I emailed CCR asking how much a 2.2L engine was. I got a return email back today with an attached PDF file of the quote. With the $375 core charge the rebuilt 2.2L is $3570. This quote failed to say if shipping was included in the price so it could be even higher. Quote Date 2/18/2008 Quote # 96 Name / Address Colorado Component Rebuilders, Inc. 5861 Marion Street Denver, CO 80216 Rep Project Total Description Qty Total 2.2L Legacy engine 3,195.00 Core Deposit (refundable) 375.00 Colorado State/Local sales tax 0.00 $3,570.00 Link to comment Share on other sites More sharing options...
msmithmmx Posted February 18, 2008 Share Posted February 18, 2008 Looks like the real deal.. Not sure how they are in business whith those prices. Link to comment Share on other sites More sharing options...
BruceyWV Posted February 18, 2008 Share Posted February 18, 2008 Only needing to sell 2 a year to pay for overheads. Link to comment Share on other sites More sharing options...
ShawnW Posted February 20, 2008 Share Posted February 20, 2008 Can you imagine less than 4 years later CCR is now charging $3570 for a rebuilt 2.2L?!!! That's absolutely rediculous. They charge a $375 core charge too. People are swapping a 2.5L for a 2.2L. Why charge a core charge on a completely different engine? Maybe they know this and will only accept a 2.2L engine as the core? Who in their right mind is going to go through the trouble of palletizing their 2.5L engine, taking it to a shipper, paying $100 or more for shipping to colorado and then hoping they refund the $375??? IMO, CCR is a very poor option now. Busa, and others. Be careful when you jump to conclusions on an internet forum. If you have a question about what CCR charges you need to simply call them. Core charges are nothing new. CCR had a few too many people not send their core engine back...including WRX cores that are nearly impossible to replace for a reasonable amount. Trusting people to send their core back no longer is an option. The $375 core charge is not rediculous. Go pull a rebuildable core from a yard. 4 hours at the yard pulling one, plus the cost of the actual engine adds up. On top of that try to buy an ej22 that is 95 and newer or an ej25 at a yard. Not easy to find a decent one and further not under 200 dollars and certainly not cheap. On top of that it doesnt matter if you send back an EJ25 core for the 2.2 core that is exactly what they expect you are doing. CCR now does their EJ22 conversion differently than it did in the past. A vast majority of the people that did the conversion had no check engine lights or problems but a small handful couldnt get rid of the codes and after spending some considerable time on the phone with those people trying to help them they developed a more foolproof way...in fact one that made the conversion more available than before as finding a 95 Legacy intake in the yard isnt terribly easy at times. They now send a blank intake manifold casting that will accept all the ej25 components. It is a brand new casting with a fuel rail setup on it. You simply transfer your intake wiring harness, fuel lines, coilpack, sensors, etc onto the new manifold from your ej25 manifold and install your rebuilt engine. This guarantees full compatibility with the wiring and passing emissions and that you wont have annoying check engine lights coming on. The product is better than ever and mine ran great. I am thinking about doing it again on my latest find (97 OBW). Link to comment Share on other sites More sharing options...
SUBARU3 Posted February 20, 2008 Share Posted February 20, 2008 tbreaden (Todd) From ,my research you cannot put the 95 EJ22 in a 99 Forester. At least easily. You run into the complications in engine management and bolting to the trans. I guess it could be done with some tweaking. I still want to do this swap on my 99 Forester of my moms. The 2.5 SOHC still scares me....not as much as the DOHC though. I'm wondering if the bellhousing for the 2.5 will fit on the 1995 EJ22? That would take care of the bolt issue at least!! Todd (yes another Todd) http://www.ultimatesubaru.org/forum/showthread.php?t=61096 http://www.ultimatesubaru.org/forum/showthread.php?t=83537 Link to comment Share on other sites More sharing options...
Bigbusa Posted February 20, 2008 Share Posted February 20, 2008 Busa, and others. Be careful when you jump to conclusions on an internet forum. If you have a question about what CCR charges you need to simply call them. Core charges are nothing new. CCR had a few too many people not send their core engine back...including WRX cores that are nearly impossible to replace for a reasonable amount. Trusting people to send their core back no longer is an option. The $375 core charge is not rediculous. Go pull a rebuildable core from a yard. 4 hours at the yard pulling one, plus the cost of the actual engine adds up. On top of that try to buy an ej22 that is 95 and newer or an ej25 at a yard. Not easy to find a decent one and further not under 200 dollars and certainly not cheap. On top of that it doesnt matter if you send back an EJ25 core for the 2.2 core that is exactly what they expect you are doing. CCR now does their EJ22 conversion differently than it did in the past. A vast majority of the people that did the conversion had no check engine lights or problems but a small handful couldnt get rid of the codes and after spending some considerable time on the phone with those people trying to help them they developed a more foolproof way...in fact one that made the conversion more available than before as finding a 95 Legacy intake in the yard isnt terribly easy at times. They now send a blank intake manifold casting that will accept all the ej25 components. It is a brand new casting with a fuel rail setup on it. You simply transfer your intake wiring harness, fuel lines, coilpack, sensors, etc onto the new manifold from your ej25 manifold and install your rebuilt engine. This guarantees full compatibility with the wiring and passing emissions and that you wont have annoying check engine lights coming on. The product is better than ever and mine ran great. I am thinking about doing it again on my latest find (97 OBW). I did have a question about what CCR charges so I emailed them. They responded with the $3195 quote. With such a high price being charged for the rebuilt engine, I don't think CCR should expect to get a core. Then again, If CCR pays shipping back to colorado for the core that would be fair. I can understand why people don't send their cores back. I've shipped some big heavy things (like a car engine) and it isn't fun or cheap. If you decide to spend $3195 for a rebuilt 2.2.L with "non residential" shipping included that's up to you. I personally think that price is incredibly high and would never spend that much. Even if the price included installation, I wouldn't do it. That's outrageous. Link to comment Share on other sites More sharing options...
ccrinc Posted February 20, 2008 Share Posted February 20, 2008 Okay. I don't usually jump into discussions about CCR, but I think it's time to get involved here because there are some miscommunications and assumptions flying that are a bit inaccurate. 1) There was an accidental error in your quote. We researched your original email and it should have been $2295. Had your reply email been to clarify and not to accuse us of smoking crack, we could have easily resolved the error immediately. (The $3195 was for the '99 EJ22, not the '96 EJ22.) That's a much more expensive engine to build since it's a hybrid between the EJ22 and the EJ25 SOHC. That price also includes non-residential shipping anywhere in the 48 states and the full gasket installation kit (all Subaru Genuine parts). 2) We have always paid for return shipping. This is nothing new. I apologize that this was not spelled out in the reply to you. I was gone for a few weeks and the usual method of replying with quotes was not utilized by the person who was handling them for me. 3) The core charge is reasonable and based on what we have to pay to replace the cores for future rebuilds. It is also refundable. Even if the block was scored beyond use, we will usually give a partial refund based on what we can salvage. 4) Admittedly, we did have a small price increase on a few (not all) engines in January because our cost of materials and machining went up substantially. (Example: machining costs alone per engine are over $250 per engine, not including clean up). We held off as long as we could on that, but eventually could not continue to absorb the higher costs to us and had no choice in the matter. Also, please remember that we won't use cheap, questionable aftermarket parts. All parts are Subaru Genuine or truly OEM when we can buy from the manufacturers who actually supply Subaru. 5) Compare our prices to the only other 2 companies who even attempt Subaru rebuilds: ATK and Jasper. I think you'll be surprised at how reasonable our engines are. And we actually stand behind our work. Now to address the gentleman who is asking about putting an EJ22 into a '99: No, it won't fit. For one thing, the bell housing is actually part of the block itself. Hope this helps to clarify things. Emily http://www.ccrengines.com Link to comment Share on other sites More sharing options...
Olnick Posted February 20, 2008 Share Posted February 20, 2008 Thanks for responding Emily. I appreciate your clarification. All the best to you and CCR. Link to comment Share on other sites More sharing options...
Bigbusa Posted February 20, 2008 Share Posted February 20, 2008 Thanks for the clarification and I'm glad to find out you're not smoking crack afterall I guess this could have all been avoided if the person giving the original quote didn't make a $900 error in price. :cool: Link to comment Share on other sites More sharing options...
Gloyale Posted February 20, 2008 Share Posted February 20, 2008 Now to address the gentleman who is asking about putting an EJ22 into a '99: No, it won't fit. For one thing, the bell housing is actually part of the block itself. Hope this helps to clarify things. Emily http://www.ccrengines.com ?????swap works the other way round????? Bells are excactly the same except 4 extra holes on the 99+ 4 bolt was good enough for the motor in it' original application, should work fine. Now making the Throttlebody/IAC/sensors work is another issue. However, I'm pretty sure someone has done it. Link to comment Share on other sites More sharing options...
ShawnW Posted February 21, 2008 Share Posted February 21, 2008 Yes, it has been done your are absolutely right on the iac, tbi, and other sensors being the problem. Link to comment Share on other sites More sharing options...
SUBARU3 Posted February 21, 2008 Share Posted February 21, 2008 I guess I'm remembering the EA71s. You could change the bellhousings to the old style, coverting the newer/fatcase EA71s. Oh I long for the simplicity of those years!!! I believe there will be more investigations and hopefully solutions, to putting the 1995 2.2 into 1999 and up vehicles. It's just a rock solid engine with no worries! Todd Link to comment Share on other sites More sharing options...
msmithmmx Posted February 21, 2008 Share Posted February 21, 2008 $2295 is still alot of flow, I would never sink that into a late 90's Subaru when you can pick a working OBW off Ebay for 3G's. I am selling my 97 OBW for 3100 this weekend. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now