Jump to content
Ultimate Subaru Message Board

manual turbo boost controller


Recommended Posts

As a continuation from the thread i started absking for specifics I think I have a better idea of what I need to know now. :rolleyes:

 

There is a design (mostlikely trademarked) called the Hallman Boost Controller that has a cable? or rod in a casing? I'd like to know what this part might be or if its possibly a locking choke cable or something like it?

 

That is one of the specific parts I'd like to know about and where I might find it.

 

PArt # 2 and #3 are more of a what *kit or otherwise were they found in for use.

The small spring and the balbarring.

Do any of these have "partnumbers" that anyone remembers or what?

 

that way i can go about building this puppy.

 

I am still interested in a Sabb"APC" 3 wire thingy but, that's down the road aways.....

 

i have seen the official HAllman site and don't feel like spending almost a Ben Franklin for the setup.

 

there that's enough for now.

Link to comment
Share on other sites

Monkster, I have built several boost pressure control mechanisms

including an electricly operated one.

The trick part is the spring - too low a rate and boost creep occurs

too high a rate and the opening closing spreads out the boost pressure window.

As for making it controlable from the cockpit. Maybe several at different pressures could be wired to solenoids so you could choose the boost for the situation.

I just leave mine at 14 psi and use my loud pedal for control.

Remember an IC will drop some boost pressure, so meter after it,

the factory gets it's control pressure right at the turbo outlet.

Hope this helps

Link to comment
Share on other sites

C'mon steve.. you're the electrical wiz, and I know a bit about saabs. Between the two of us, we can figure out the Saab APC system.. oh yeah.. I found my Saab Haynes manual.. can't find the bentley though.. still in a box somewhere.

Link to comment
Share on other sites

Alright already... I'll play with the SAAB part when i get's back from Nevada via boulder Colorado.

 

 

Ummmmm I was just hoping to find out if the HALLMAN boost controller 's manual wire tube thingy was a part with a "known name" like a choke cable or some such name with a part number like -ohhhh a SLR Camera has a manual finger trigger that has a locking disk on it to hold the shutter wide open for a opperator to be determinded time then closes it without giggling the camera.

 

 

does this make a clearer picture.... it's be like having a "volume" control knob for the turbo as i have the A/F and the boost/vac gauges installed and op'ing fine.

 

ugghh its time for sleep.... good night alll

Link to comment
Share on other sites

infinitely variable boost pressure control

I have my igniton timing set up that way

actually uses a manual choke knob and cable.

I have never seen a part number for cable only in Hallman's set up.

There is what you are refering to eh?

proevo1.jpg

It appears to be as you said a cable turned "volume control" for the boost pressure

The cable turns the black knob on this

essm.jpg

This is the one I now use BTW.

Seems to be a simple "rig"

You do not have to turn the knob very much so a flat disc fastened to the knob and the turn the disc like you open close a lawn mower throttle or choke

Okay I'll get back at ya on this one.

Link to comment
Share on other sites

look into using parts of a old spedo cable or even a dremel flexi shaft thingy

 

with a small sluminum cylinder drilled out to the correct size to fit over the valve stem with one maybe 2 grubs screws per side of said doohicky

Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
 Share

×
×
  • Create New...