kiwirx Posted February 12, 2005 Share Posted February 12, 2005 I have an RX Turbo rally car with numerous mods and have been running 15-17 psi boost but have finally blown a piston to bits.I would like to increase the compression ratio and reduce the boost to achieve better low down power and less lag ,hopefully giving better driveability.I guess the easiest way would be to use a non turbo carb type EA82 block.Does anyone know if this is possible and weather the internals differ. Link to comment Share on other sites More sharing options...
GLCraig Posted February 13, 2005 Share Posted February 13, 2005 There are a couple of differences in the N/A and the Turbo blocks. The Turbo block has the hole to screw the knock sensor in and an addition crankcase ventelation port. If your block is not dammaged by the bad piston, you might look into getting some higher compression pistons instead. The carburated and MPFI version of the EA82 had a 9:1 ratio and the SPFI (throttle body injection) version had a 9.5:1 ratio. Link to comment Share on other sites More sharing options...
ogordon Posted February 13, 2005 Share Posted February 13, 2005 There are a couple of differences in the N/A and the Turbo blocks. The Turbo block has the hole to screw the knock sensor in and an addition crankcase ventelation port. If your block is not dammaged by the bad piston, you might look into getting some higher compression pistons instead. The carburated and MPFI version of the EA82 had a 9:1 ratio and the SPFI (throttle body injection) version had a 9.5:1 ratio. Does the turbo block for the 82t have the oil jets for cooling the pistons like the ej series turbo engines? If so this would be a good reason to stick with the turbo block. Link to comment Share on other sites More sharing options...
calebz Posted February 13, 2005 Share Posted February 13, 2005 Does the turbo block for the 82t have the oil jets for cooling the pistons like the ej series turbo engines? If so this would be a good reason to stick with the turbo block. No and IIRC, the EJ22 is the only one of the EJ turbos (USDM) with the oil squirters. As far as the differences in the Blocks between the EA82 carb and EA82T. Different pistons - flat (9.0:1) instead of dished (7.7:1) PCV - Carb block doesn't have the hole in the top of the block for the PCV pipe. Not really a big deal. Can be dealt with Knock sensor - while the carb block doesn't utilize the knock sensor, the spot is there for it, and is already threaded. How do I know? I have one Link to comment Share on other sites More sharing options...
MilesFox Posted February 13, 2005 Share Posted February 13, 2005 a carb block would be ideal. use the turbo heads and intake, carb bottom end. the hole for the knock sensor is present on the block. the crankcase vent is not there but you can bypass that here is what is involved, me and a buddy built turbos on a carb block for an RX www.warpthree.com/milesfox/87rx/rxbuild Link to comment Share on other sites More sharing options...
Caboobaroo Posted February 13, 2005 Share Posted February 13, 2005 [hyjack] heh I found a pic of the hose that created the leakage on my RX motor http://www.warpthree.com/milesfox/87rx/rxbuild/oilhose.jpg [/hyjack] Link to comment Share on other sites More sharing options...
Frank B Posted February 13, 2005 Share Posted February 13, 2005 a carb block would be ideal. use the turbo heads and intake, carb bottom end. the hole for the knock sensor is present on the block. the crankcase vent is not there but you can bypass that here is what is involved, me and a buddy built turbos on a carb block for an RX www.warpthree.com/milesfox/87rx/rxbuild Thanks for posting those photos! What was the reason for the piston mods, and what was the result? Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now