starkiller Posted March 7, 2005 Share Posted March 7, 2005 well, since i cant afford a new o2 sensor and havent found any in the yards yet and i dont have the electrical test equipment to test the one that is apparently bad, i will have to let this problem go for awhile...is there any harm in this? Link to comment Share on other sites More sharing options...
hooziewhatsit Posted March 7, 2005 Share Posted March 7, 2005 It'll make the car run rich, and could eventually clog the catalytic converter I believe. A generic bosch sensor will work just fine, and be much cheaper than an OEM one. Only difference is that with the generic one, you need to cut and splice the connector on it from the one currently in the car. I think they only cost about 25ish. Link to comment Share on other sites More sharing options...
Sweet82 Posted March 7, 2005 Share Posted March 7, 2005 Starkiller, What car are we talking about Glenn, 82 SubaruHummer 01 Forester "the check's in the mail" Link to comment Share on other sites More sharing options...
starkiller Posted March 7, 2005 Author Share Posted March 7, 2005 its an 89 spi wgn....and i just replaced the o2 sensor a couple of months ago with a bosch so it would pass emissions....car is getting good mileage, around 31 mpg so its not running rich yet has some stumbling and hesitation though at accleration and going up hills...see previous post about this problem Link to comment Share on other sites More sharing options...
starkiller Posted March 8, 2005 Author Share Posted March 8, 2005 bumpo Link to comment Share on other sites More sharing options...
NorthWet Posted March 8, 2005 Share Posted March 8, 2005 Alan, I have some doubt that that replacement Bosch sensor would be bad enough to cause CEL error codes, yet good enough to not kill your mileage. Is it possible that you are seeing an old code? (As in, did you clear old codes since your e-testing?) If I remember correctly, the O2 sensor code occurs when the ECU detects its "reference voltage" (5V) or 0V (out of range values). (Info provided by another board member in another, older thread.) This would imply something really bad happened to the O2 sensor. My guess as to what would happen is that the ECU would go "open loop" and use default mixture settings, which is probably richer. I doubt that plugging up of the catcon would occur, at least not unless it went super rich and for a significant period of time. Link to comment Share on other sites More sharing options...
starkiller Posted March 8, 2005 Author Share Posted March 8, 2005 no, not an old code...light came on during the trip back from tacoma...got home and plug the green connectors together, light went off, unplugged them, light came back on with a 32 code... Link to comment Share on other sites More sharing options...
Cougar Posted March 8, 2005 Share Posted March 8, 2005 Perhaps it may just be a bad connection to the sensor causing this. I would check the wiring for a problem. The sensor could have had a premature failure though. Does it have a warranty? Link to comment Share on other sites More sharing options...
erik litchy Posted March 8, 2005 Share Posted March 8, 2005 that was cheaper if you get a universal one that you need to splice in. it was like $12 Link to comment Share on other sites More sharing options...
hooziewhatsit Posted March 8, 2005 Share Posted March 8, 2005 If you have an ohmmeter, I'd check the grounding for the O2 sensor. To get the best reading, disconnect the ground terminal from the battery and measure the resistance to the O2 sensor. Could be the resistance is higher than it should be, causing the ECU to have trouble reading the correct voltage from it. I'd venture to guess if the resistance is higher than 1ohm, you should look into running another ground line to it. Link to comment Share on other sites More sharing options...
starkiller Posted March 9, 2005 Author Share Posted March 9, 2005 dont have any kind of electrical test stuff at all...no warranty as far as i know.. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now