MorganM Posted September 5, 2003 Share Posted September 5, 2003 Took the day off and need to run alot of errands. The tool store is on my TO-GO list! Need to know what size socket I need for the stub axle castle nut on a 1988 GL wgn. Would also like to get the right size/type of punch to remove DOC/CV pin. I would also like to plead for your trade secrets on the quickest and most efficient way to change an axle assembly. If you do not wish to divulge such detals; I completly understand Thank you. Link to comment Share on other sites More sharing options...
Caboobaroo Posted September 5, 2003 Share Posted September 5, 2003 its a 36mm Link to comment Share on other sites More sharing options...
MorganM Posted September 5, 2003 Author Share Posted September 5, 2003 wow Quick response, thx! Is there a difference in size between 2WD and 4WD ? I have all 2WD stuff on right now. Will be putting in the 4WD rear end tomarrow night so then I'll have 2WD / 4WD untill I get the 5speed DR in. Do the 2WD inner CVs hook upto the 4WD DR transmission? Or will I be needing to swap in 2 more 4WD front axle assemblies? Thx Link to comment Share on other sites More sharing options...
Hogsubie Posted September 5, 2003 Share Posted September 5, 2003 I'm about to do the same albeit I'm not converting from 2wd to 4wd. I've got to change the front axle. Do yall recommend impact (air tools) for removal? I'd rather not buy a regular socket and not be able to remove it. To reiterate one questions. What's the recommended punch size? Are there any other tools needed? All suggestions are welcome. Jason Link to comment Share on other sites More sharing options...
mcbrat Posted September 5, 2003 Share Posted September 5, 2003 I use a 3/16 pin punch. it's a blue one sold at my local Ace Hardware store. there is a specific Craftsman one that works as well... Link to comment Share on other sites More sharing options...
Russ Hill Posted September 5, 2003 Share Posted September 5, 2003 An impact wrench if good but not needed. Just leave tires and wheels mounted and break it loose with the car on the ground. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 5, 2003 Share Posted September 5, 2003 I think EA82 2WD axles are indeed different than the 4WD ones. Someone correct me if I'm mistaken. Also - check this thread for axle removal / installation: http://usmb.ultimatesubaru.org/forum/showthread.php?s=&threadid=2576&highlight=axle+removal And try out the search feature next time as you may have run across this on your own, and saved yourself some time. GD Link to comment Share on other sites More sharing options...
Svengouli7 Posted September 6, 2003 Share Posted September 6, 2003 2wd axles might be a little less beefy...dunno for sure. only differences I was aware of for sure is in the spline count between turbo and non axle ends. Drawing the axle into the hub has been a pita for me before. Have some plastic ABS or PVC pipe handy to cut into spacers to place behind the axle washer and nut if needed. I have had the whole knuckle off before w/ the axle just started... and WWF'd the face of the knuckle on the garage floor w/ axle in hands to get it seated good.. prolly lucky I didn't break anything though Link to comment Share on other sites More sharing options...
Qman Posted September 6, 2003 Share Posted September 6, 2003 The nut size varies depending on wether or not it is a OEM new or rebuilt axle or an aftermarket axle. 36mm for standard and 32mm for the other. The punch needs to be a 3/16ths. The difference between 2wd and 4WD axles is the size of the shaft. 2wd axels are thinner than 4WD axles. Link to comment Share on other sites More sharing options...
MorganM Posted September 6, 2003 Author Share Posted September 6, 2003 Great info guys, thanks alot. GeneralDisorder: Search is great; and your right I should have used it for the "how too" question but there wasnt a big consensus on what size the nut was and no mention of the punch size. Off to the parts store again! Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now