1978brat Posted June 14, 2005 Share Posted June 14, 2005 I was wondering if the 1800 bolts right up to the trans-axle in my '78 brat. i know that the engines are the same size, exterior dimensions-wise, but i wasn't quite sure about the internals, splines, etc. i was rebuilding my 1600 when i scored this 1800 for free, and it's only got like 35000 original miles on it. i was really hopin' to use it with out pullin' the transaxle, but it's no biggie if i have to is it? lemme know asap if ya got any info for me. thanks a ton, Flynt Link to comment Share on other sites More sharing options...
Caboobaroo Posted June 14, 2005 Share Posted June 14, 2005 If the 1800 has the starter top mounted, then yes it will bolt in. If it has a side mounted starter (will be off to the driver's side) then it won't unless you either A. get an 1800 tranny that will have the same bellhousing that matches the engine or B. if it'll work, bolt the 1600 belhousing to the 1800 engine and it should mate up. Link to comment Share on other sites More sharing options...
1978brat Posted June 14, 2005 Author Share Posted June 14, 2005 thanks, option b was my original plan. just have the 1800 engine bolt right to the 1600 trans-axle and bell housing, etc. and, how's wiring match up? as far as i can see, everything looks the same or very easily changable. anything i should be aware of? thanks for your help. Flynt Link to comment Share on other sites More sharing options...
Caboobaroo Posted June 14, 2005 Share Posted June 14, 2005 everything should be the same since they did use the same carb depending on the year of car it was taken from. If it's the two barrel Hitachi, it'll be the same but if it is the one barrel Carter-Weber, you'll have to do a swap to the two barrel in order for it to be the same. Search around, a few people have swapped and posted about it Link to comment Share on other sites More sharing options...
Zefy Posted June 15, 2005 Share Posted June 15, 2005 welcome! i looked into this... ok there is no such thing as a top mounted starter on an 1800 engine... i went and found the only 81 brat in the area and took a look... if you can get the bellhousing to fit then you're half way there... you also need the belly pan from and 1800... or fab something to make it fit... the mounting points aren't the same from what i saw... Link to comment Share on other sites More sharing options...
bratsrus1 Posted June 18, 2005 Share Posted June 18, 2005 Hey Zefy This is Jerry,i call BS on that one because i have a EA81 with a 5 speed front wheel drive 86 hatch that has that bellhousing. It will be up for sale when i part the car out soon. Thanks Jerry Link to comment Share on other sites More sharing options...
subGSR Posted June 18, 2005 Share Posted June 18, 2005 The EA81 is wider than the EA71 as it has a longer stroke to give it the cc rating of 1800. The bellhousing of a EA71 will not fit the EA81. The intake manifold of a EA71 will not fit a EA81. The starter motor is on the top of the EA71 and on the side in the EA81. Link to comment Share on other sites More sharing options...
1978brat Posted June 18, 2005 Author Share Posted June 18, 2005 so, back to my original question....am i going to be able to fit the ea81 into by brat with ease, or am i gonna need to do some fab work, etc.? i planned on taking the whole transaxle, and engine out as one. i was pretty sure they wouldn't match up, i was just checking. thanks for all the help. Flynt Link to comment Share on other sites More sharing options...
bajavwnsoobnut Posted June 19, 2005 Share Posted June 19, 2005 the EA-81 tranny will fit in and the holes to mount the tranny mounts are there and should be tapped so it can be easily bolted in you will need the clutch cable from the doner car the linkage for the main shifter should work but the 4wd shifter might need to be modified a lil bit at the end to make it work but should be ok for the rest of it cause the holes are there for the shifter tent the 1800 will work just need to get the throttle cable from the doner too IIRC but all and all everything should fit Link to comment Share on other sites More sharing options...
Rockman Posted July 20, 2005 Share Posted July 20, 2005 I've thought of doing this as well. Question. If you install the EA81 and matching transmission can you use the driveshaft from the EA71 or do you need the one that went with the EA81? Link to comment Share on other sites More sharing options...
bajavwnsoobnut Posted July 21, 2005 Share Posted July 21, 2005 same driveshafts Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now