soobscript Posted August 11, 2005 Share Posted August 11, 2005 I'm about to start a head gasket job. Can someone direct me to or tell me all the gaskets and seals I will need? Link to comment Share on other sites More sharing options...
hooziewhatsit Posted August 11, 2005 Share Posted August 11, 2005 I just finished this same job; just got the car running this morning :-) the seals you need really depends on what all you want to reseal. Personally, I resealed everything. list of everything (I think) 2x HGs 11044AA013 2x cam tower o-ring (between head & cam tower) 13089AA010 2x cam o-ring 806958020 2x cam seal 806738040 1x front main seal 806738070 1x rear main seal ? (I didn't order one) 1x 'mickey mouse' oil pump seal 14066AA000 1x oil pump seal 806718090 1x oil pump o-ring 806945020 1x oil pan gasket 11121AA001 1x water pump gasket 21114AA000 1x water pump o-ring 806927010 2x intake gasket 14035AA150 RH valve cover gasket 13270AA001 LH valve cover gasket 13272AA001 optional: timing belt cover gaskets if you need, I can dig up SOA part numbers for most of these also. terminology: o-ring = uhh, an o-ring . Seal = 1/4" wide, 1/4" deep seal, like the front main seal. gasket = flat thingy. good luck and take your time. Hopefully you're taking the engine out for this if it's your first time. EDIT: Added SOA part numbers for all the seals/gaskets. Word of warning though... when you order these, make sure they are the correct ones. I had to cross check prices with the part number with the drawing at 1stsubaruparts.com to get some of them, since I already used the seals and just had empty bags! Link to comment Share on other sites More sharing options...
soobscript Posted August 20, 2005 Author Share Posted August 20, 2005 Okay, I have a few questions about some of these... 2x cam o-ring - are these the two rings on the actual shaft? 2x cam seal - on the front engine end of shaft behind pulley? Subaru part #'s for these? (didn't find in online catalog) Quote 2x cam tower o-ring (between head & cam tower)1x front main seal 1x 'mickey mouse' oil pump seal 1x oil pump seal 1x oil pump o-ring 1x water pump gasket 1x water pump o-ring 2x intake gasket Link to comment Share on other sites More sharing options...
erikvr Posted August 22, 2005 Share Posted August 22, 2005 then there's the seal to seal the seals Link to comment Share on other sites More sharing options...
hooziewhatsit Posted August 22, 2005 Share Posted August 22, 2005 soobscript said: Okay, I have a few questions about some of these... 2x cam o-ring - are these the two rings on the actual shaft? 2x cam seal - on the front engine end of shaft behind pulley? Subaru part #'s for these? (didn't find in online catalog) when you get the cam sprocket off, there are two 10mm bolts that hold a 'guide' for the cam. Once this is out the entire Cam can be removed. The o-ring goes between this and the cam tower. The cam seal is where the cam spins inside it. If that made any sense at all. I'll try to get the SOA #s tomorrow... most of the bags are empty now so they may be wrong... (hope not) Link to comment Share on other sites More sharing options...
sregor13 Posted August 24, 2005 Share Posted August 24, 2005 After you remove the Cam Sprocket the next thing there is I think is referred to by some as the "cam seal housing". The cam seal goes in the front of it,(the housing that is) and the cam o-ring goes on the back side of this thing. That is as far as I went. Hope that helps Link to comment Share on other sites More sharing options...
stephenw22 Posted August 24, 2005 Share Posted August 24, 2005 Don't forget exhaust gaskets! (I almost did) Get turbo gaskets if you can, they seem a lot better than the "normal" ones. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now