SuBrat84 Posted September 11, 2005 Share Posted September 11, 2005 Been workin on Smoke a little bit lately.. got it down to needing new rubber fuel lines.. a fuel pump relay.. and preferrably a better fuel pump than one out of an ea82. It needs some suspension work as the air system is a bit glitchy right now. http://gallery.usmb.net/albums/album17/XT6Front.jpg[/img]"] There it is.. up on blocks.. You can see the GT off to the right and Lurch in the back. That's Jessicas Honda Accord SW in the back. http://gallery.usmb.net/albums/album17/ER27_2.jpg[/img]"] A good overhead shot of the ER27. She screams. http://gallery.usmb.net/albums/album17/ER27_Dirty.jpg[/img]"] Here it is Before I cleaned it... Cleans up nice doesn't it?!! Anyway... I'm dying to have this car on the road. Really the only question I have at this point is about the hood not closing flush... Is it possible it was in a minor front end collision and bent the hood supports? Or something weird bent the hood supports?? If anyone has any XT6 with a hood that close flush could you snap some pics of the bracket mount area inside the engine bay?? I think mine is bent.. but I don't want to try to "unbend" it if it's not bent.. ya know. Link to comment Share on other sites More sharing options...
NorthWet Posted September 11, 2005 Share Posted September 11, 2005 ... at this point is about the hood not closing flush... Are the rubber bumpers on each fender channel adjusted properly? (I assume that the XT-series have these.) Link to comment Share on other sites More sharing options...
Turbone Posted September 11, 2005 Share Posted September 11, 2005 You can try and adjust the bottom latch, loosen it and drop it down some. Link to comment Share on other sites More sharing options...
soobmater Posted September 11, 2005 Share Posted September 11, 2005 u did a very good job cleaning the engine.nice work, its comin along. i also thought about the ruber bumpers because mine wern't adjusted correctly when i got the car. Link to comment Share on other sites More sharing options...
benebob Posted September 11, 2005 Share Posted September 11, 2005 Are the rubber bumpers on each fender channel adjusted properly? (I assume that the XT-series have these.) Yeah it has 'em. Round dough nut looking things. Link to comment Share on other sites More sharing options...
subyrally Posted September 11, 2005 Share Posted September 11, 2005 what you use to clean the engine? Link to comment Share on other sites More sharing options...
benebob Posted September 11, 2005 Share Posted September 11, 2005 I've found that fantastik does a great job considering it is CHEAP and a good grease cutter. Not sure what he used here but for an engine bay, esp a white engine bay it works wonders. Link to comment Share on other sites More sharing options...
SuBrat84 Posted September 12, 2005 Author Share Posted September 12, 2005 what you use to clean the engine? Dish Soap (with bleach alternative), Carb Cleaner, Water & Compressed Air. Dying for a steam cleaner to get the tougher grease you can't see in the pics... Link to comment Share on other sites More sharing options...
Turbone Posted September 12, 2005 Share Posted September 12, 2005 Whatever you do, dont use dishsoap on the exterior paint. It leaches out the oils in the paint and dulls the finish. Link to comment Share on other sites More sharing options...
SuBrat84 Posted September 13, 2005 Author Share Posted September 13, 2005 Whatever you do, dont use dishsoap on the exterior paint. It leaches out the oils in the paint and dulls the finish. Thanks for the tip... I usually use laundry detergent on the exterior... any good suggestions?? Link to comment Share on other sites More sharing options...
Turbone Posted September 13, 2005 Share Posted September 13, 2005 Sure, you can buy the good stuff at any parts store. Most major wax brands make it. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now