MaroonDuneDoom Posted October 17, 2003 Share Posted October 17, 2003 i have an ea82 engine and was wondering how i might build an economical custom cold air intake. has anyone built there own from scratch. i'm sure someone has. any ideas would be greatly appreciated. Link to comment Share on other sites More sharing options...
Snowman Posted October 17, 2003 Share Posted October 17, 2003 I have made a ghetto cold-air intake for my car, and it works great. Currently, it is not hooked up, and I can tell the difference in performance, which is great for a mod that cost me about a dollar. Mine is not set up as a "true" cold air intake, in that it just dumps lots of outside air onto a foam filter connected to the intake. I did that because I don't want to suck any water while offroading. Materials I used: 2 heater air duct hoses from a '78 subaru wagon (you can use any flexible plastic pipe, those just have the right curves and each section about a foot long) 1 section of pvc pipe about 10 inches long a crapload of duct tape and plastic zip-ties How to hook it up: Attach one of the flexible tubes to the bottom of the bumper in the corner of the radiator air inlet on the passenger side using the zip-ties so that it is facing forward and can take in a lot of air. Route this hose so that it goes into the inner fenderwell (you have to at least loosen the big plastic piece inside the fender in order to get to everything). There is just enough room to fit it through a large gap, although it's kinda tight. Using duct tape, attach the pvc pipe to the flexible tube and attach the other flexible tube to the pipe and run the tube up into the engine bay so that it shoots air out onto your intake. I am assuming you have an SPFI ea82. In your case, I would recommend just duct-taping the tube onto the air inlet that is already in your inner fenderwell. Either that or if you want to cut holes in your air box for better flow, run the tube into the engine bay and point it toward the holes. Another alternative is to create a snorkel in the same fashion, which would serve the same purpose, but would look really neat and would virtually eliminate the issue of sucking in water. Link to comment Share on other sites More sharing options...
soobme Posted October 17, 2003 Share Posted October 17, 2003 SPFI? MPFI? Carb? What type of AFM are U working with? If U don't know post a pic of the curent air intake. I made one for my turbo out of some steel, a wrecking yard rubber elbow and a UNI foam air filter element. Link to comment Share on other sites More sharing options...
calebz Posted October 17, 2003 Share Posted October 17, 2003 Keep in mind that you can make a "better" air intake, but it won't be a "cold" air intake if it is drawing air from under the hood.. needs to get cold air from somewhere outside the engine compartment.. still, even drawing air from under the hood is preferrable to the crappy stock restrictive airboxes Link to comment Share on other sites More sharing options...
MaroonDuneDoom Posted October 17, 2003 Author Share Posted October 17, 2003 i'm running spfi. sorry bout that, kinda slipped my mind. i already did an airbox mod (cut out) and noticed quite a bit of improvement. so, just feed air to a high flow cone filter? i was thinking that what i would do would be to make a venturi of sorts in which i would stretch the end closest to the filter and fit it nice and close. would this be a good idea to mount the end of this air inlet tube really close to a cone filter or should i leave a few inches¿ Link to comment Share on other sites More sharing options...
Dante Posted October 17, 2003 Share Posted October 17, 2003 I've been looking around. K&N makes a round filter with a filter top that will work with a Weber (it is the same as the round filter I have seen in some Weber pics, but has a top filter element, too). It gives you a HUGE surface. Pipercross also makes some large oiled foam filters for Webers. In both cases, I'd be a little worried about wetting them. I've also seen a few remote filter adapters for Webers. They would allow you to mount the filter or an inlet somewhere open to cold air. Again, you'd want to think about puddles and rain. Link to comment Share on other sites More sharing options...
pntball&wheelin Posted July 24, 2006 Share Posted July 24, 2006 http://www.powerfloracing.com/spectre-home.asp They have a build your own CAI. You can purchase the pieces at Autozone, Pep boys, and A&A Auto parts stores. The pieces are reasonable and you can build it any way you want, even put 2 air filters in seperate locations. Andy Link to comment Share on other sites More sharing options...
idosubaru Posted July 24, 2006 Share Posted July 24, 2006 that link doesn't work...my machine or bad link? Link to comment Share on other sites More sharing options...
azsubaru Posted July 24, 2006 Share Posted July 24, 2006 http://www.powerflowracing.com/spectre-home.asp He just missed a 'w' Link to comment Share on other sites More sharing options...
mikeshoup Posted July 24, 2006 Share Posted July 24, 2006 *cough* this thread is dated 2003. Anyone else notice that? Link to comment Share on other sites More sharing options...
Caboobaroo Posted July 24, 2006 Share Posted July 24, 2006 lets bust out the shovel and go post digging:lol: Link to comment Share on other sites More sharing options...
rllywgn Posted July 24, 2006 Share Posted July 24, 2006 i thought it was april fools day again... thread pruning.. rllywgn Link to comment Share on other sites More sharing options...
azsubaru Posted July 24, 2006 Share Posted July 24, 2006 *cough* this thread is dated 2003.quote] Well I knew it, but I wasn't sure you knew. Link to comment Share on other sites More sharing options...
bgd73 Posted July 24, 2006 Share Posted July 24, 2006 i'm running spfi. sorry bout that, kinda slipped my mind. i already did an airbox mod (cut out) and noticed quite a bit of improvement.so, just feed air to a high flow cone filter? i was thinking that what i would do would be to make a venturi of sorts in which i would stretch the end closest to the filter and fit it nice and close. would this be a good idea to mount the end of this air inlet tube really close to a cone filter or should i leave a few inches¿ Venturi works good on spfi. The end result going into intake needs a stubborn, fast flow to get any true benefit of cool air intake.without restriction, but for venturi flow purpose only.Just opening it up into a sloppy open mess doesn't do any bit of good but make noise-- ya gotta make it flow to benefit. Don't even bother getting air inside engine compartment. You have good ideas there... Link to comment Share on other sites More sharing options...
subarubrat Posted July 24, 2006 Share Posted July 24, 2006 For the XT6, you can buy the MAF adapter for the Toyota previa and buy a K&N cone. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now