TROGDOR! Posted October 19, 2003 Share Posted October 19, 2003 Any tips on removing the EA82 front bumper cover before I dig into it? Link to comment Share on other sites More sharing options...
StormTrooper Posted October 19, 2003 Share Posted October 19, 2003 Don't remove the cover!! If you are swapping complete bumpers, removing the cover will get you no where...If you are swapping covers for aesthetics, then go right ahead. But if you removing the whole bumper, you need to get at it from inside the hood. Pretty sure you need to remove the battery to get in there, or, its just very close. On both sides of the body under the hood are two 17 or 19mm bolts..Do not make the mistake i made and break the nuts that are spot-welded onto the bumper off, it will cause a slightly more intense headache...It should be very simple...just unscrew four bolts from under the hood, and Voila!! Good Luck Link to comment Share on other sites More sharing options...
Flowmastered87GL Posted October 19, 2003 Share Posted October 19, 2003 Yep just remove 4 bolts from the engine bay. Removing the battery DOES make it easier. Its a little harder when the bumper is tweaked like 10 degrees (my 86 battlewagon) 1 Link to comment Share on other sites More sharing options...
StormTrooper Posted October 20, 2003 Share Posted October 20, 2003 you should have seen me in the J/Y...Didn't realize the nuts were spot welded on the bumper...shaved my knuckles, yelled and buymped my head, broke all four nuts off their welds, had a helluva time finding where the bolts were located, I caould have sworn they were somewhere secret...Then accidentally found where they were located, and then felt incredibly smart! I wouldn't wish that experienmce on anyone, but I'm sure we've all done some smart stuff when it comes to fixing/screwing with cars... good luck Trogdor. (cool name...is your name Rodgor T?) 1 Link to comment Share on other sites More sharing options...
AWD J3wman Posted July 26, 2014 Share Posted July 26, 2014 This too should be stickied or put in the FAQs Link to comment Share on other sites More sharing options...
MR_Loyale Posted July 27, 2014 Share Posted July 27, 2014 (edited) Front bumper. This may help: The writeup of the procedure is here: http://www.autozone.com/autozone/repairguides/Subaru-Coupes-Sedans-Wagons-1985-1996-Repair-Guide/EXTERIOR/Bumpers/_/P-0900c15280067754 Edited July 27, 2014 by MR_Loyale Link to comment Share on other sites More sharing options...
AWD J3wman Posted July 28, 2014 Share Posted July 28, 2014 super easy to get to. took me 20 mins with an AC system and I have never done it before. Slid right out, no trickery involved. Link to comment Share on other sites More sharing options...
Ibreakstuff Posted July 28, 2014 Share Posted July 28, 2014 Sticky or put into the repair section! Definitely good information, glad I am not the only person that learned the hard way regarding the front bumper bolts.And WOW did autozone upgrade their repair guides, thanks for that gem as well. Link to comment Share on other sites More sharing options...
Subarocket Posted July 28, 2014 Share Posted July 28, 2014 Jewman, what did you use? Those lines were getting in the way every chance they could. I think there was a radiator hose or big group of wires as well. It was over a year ago, hence I don't remember details, but I am about to do it again. Link to comment Share on other sites More sharing options...
Subarocket Posted July 28, 2014 Share Posted July 28, 2014 Am I the only one who doesn't see anything on that auto zone link? Just a menu... Link to comment Share on other sites More sharing options...
Subarocket Posted August 16, 2014 Share Posted August 16, 2014 My new car is without AC and not rusty. It took me less than ten minutes to remove my front bumper. Did not remove the battery or anything. Just a short handled socket wrench and a short 14mm socket. No extender bits or anything and it slipped in front of all the wiring. For some reason I remembered the bolts being below that lip on the frame and closer to the valve covers. If you are having troubles removing your bumpers, just buy a car from a rust free area Link to comment Share on other sites More sharing options...
AWD J3wman Posted August 18, 2014 Share Posted August 18, 2014 Jewman, what did you use? Those lines were getting in the way every chance they could. I think there was a radiator hose or big group of wires as well. It was over a year ago, hence I don't remember details, but I am about to do it again. 6" extension, with a 14mm socket, my radiator was out so that might of helped but everything moved pretty easily. Link to comment Share on other sites More sharing options...
AWD J3wman Posted September 17, 2014 Share Posted September 17, 2014 Do XT bumpers remove the same way? Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now