Monte Posted June 10, 2006 Share Posted June 10, 2006 I can't really tell for sure where the leak is, should it be really obvious? The valves in one cylinder did look damp, like I would imagine it would if it had some coolant on it. The others looked dry. And when I was removing the cams, some of the bolts had a little bit of water under pressure under them. When I first untorqued them I got a little pffft and some drops of water. 3-4 bolts under the valve cover did this and 1-2 of the bolts holding the seals did it too. What's up with that? I'm not totally sure, but I think a couple head bolts came out wet too, not sure what to think there either. Thanks, Monte Link to comment Share on other sites More sharing options...
Monte Posted June 11, 2006 Author Share Posted June 11, 2006 :-\ Link to comment Share on other sites More sharing options...
macdonaldks Posted June 11, 2006 Share Posted June 11, 2006 Replaced the head gaskets on my 97 OBW 40,000 Km ago and so far everything is fine. I too was wondering the same thing as I stared at the parts in front of me. I had exhaust gases visible in my coolant overflow bottle but the original head gasket appeared fine. Once I started peeling the layers of the gasket apart, I could see obvious places where the exhaust gases were getting into the cooling system. This made me feel a little better about doing the whole job... Regards; Ken Link to comment Share on other sites More sharing options...
ShawnW Posted June 11, 2006 Share Posted June 11, 2006 Its not always obvious. Be absolutely sure the head and block surfaces are PERFECTLY flat before reassembly. Link to comment Share on other sites More sharing options...
Monte Posted June 12, 2006 Author Share Posted June 12, 2006 ShawnW said: Its not always obvious. Be absolutely sure the head and block surfaces are PERFECTLY flat before reassembly. Can I do that myself? I can easily take the heads in, but the block? I've seen pictures of checking the heads with a straight edge and feeler guage, but where do I get a good straight edge? Monte Link to comment Share on other sites More sharing options...
Monte Posted June 12, 2006 Author Share Posted June 12, 2006 macdonaldks said: Replaced the head gaskets on my 97 OBW 40,000 Km ago and so far everything is fine. I too was wondering the same thing as I stared at the parts in front of me. I had exhaust gases visible in my coolant overflow bottle but the original head gasket appeared fine. Once I started peeling the layers of the gasket apart, I could see obvious places where the exhaust gases were getting into the cooling system. This made me feel a little better about doing the whole job... Regards; Ken Yeah, it'd be nice to see the leak. I'll look closer at the gasket. Monte Link to comment Share on other sites More sharing options...
JPX Posted June 12, 2006 Share Posted June 12, 2006 If you need a reference point, here is a photo from Skip's head gasket changeout page: Link to comment Share on other sites More sharing options...
Monte Posted June 12, 2006 Author Share Posted June 12, 2006 So, do you think that where the black stuff is gone is where it's been leaking? If that's the case, there's no doubt mine were leaking. I'll post some pictures later to show. Thanks, Monte JPX said: If you need a reference point, here is a photo from Skip's head gasket changeout page: Link to comment Share on other sites More sharing options...
Ranger83 Posted June 12, 2006 Share Posted June 12, 2006 Monte said: Can I do that myself? I can easily take the heads in, but the block? I've seen pictures of checking the heads with a straight edge and feeler guage, but where do I get a good straight edge? Monte The heads are almost always distorted a bit. Any automotive machine shop can mill them flat again. It's not very expensive. Link to comment Share on other sites More sharing options...
nipper Posted June 12, 2006 Share Posted June 12, 2006 Monte said: Can I do that myself? I can easily take the heads in, but the block? I've seen pictures of checking the heads with a straight edge and feeler guage, but where do I get a good straight edge? Monte a steel ruler is the standard straight edge. Just dont by a cheap one. nipper Link to comment Share on other sites More sharing options...
Monte Posted June 13, 2006 Author Share Posted June 13, 2006 nipper said: a steel ruler is the standard straight edge. Just dont by a cheap one. nipper What's a "not cheap" steel ruler? I'm a carpenter, I've got "steel rulers" all over the place. None were cheap to me, but I'm not sure if I'd trust them to check my heads and/or block. Monte Link to comment Share on other sites More sharing options...
nipper Posted June 13, 2006 Share Posted June 13, 2006 Monte said: What's a "not cheap" steel ruler? I'm a carpenter, I've got "steel rulers" all over the place. None were cheap to me, but I'm not sure if I'd trust them to check my heads and/or block. Monte Thats all you really nees, is a steel ruler or a machinest ruller. As long as they are solid steel they will have a perfect straight edge on them. You check the heads in the x, y, and diagnol directions. nipper Link to comment Share on other sites More sharing options...
ShawnW Posted June 13, 2006 Share Posted June 13, 2006 A steel ruler isnt going to be precise enough in this case. The tollerance is very low. Snap-On sells a straight edge that would be way overkill for a do it yourselfer but its obviously good enough. I have a feeling that if you put your shortblock in the trunk of a car and took it with you to the place that you have your heads surfaced at they might check the block for you for a few bucks. Link to comment Share on other sites More sharing options...
nipper Posted June 13, 2006 Share Posted June 13, 2006 ShawnW said: A steel ruler isnt going to be precise enough in this case. The tollerance is very low. Snap-On sells a straight edge that would be way overkill for a do it yourselfer but its obviously good enough. I have a feeling that if you put your shortblock in the trunk of a car and took it with you to the place that you have your heads surfaced at they might check the block for you for a few bucks. Steel rule is good enough for a flatness check, as he isnt going to be taking dimensions off it. Now if he was going to do dimensions thats an entirely differnt ball game. nipper Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now