subeman90 Posted September 18, 2006 Share Posted September 18, 2006 Post #1 has been copied and posted in the USRM! Great writeup and good luck with your set up. Link to comment Share on other sites More sharing options...
beataru Posted September 18, 2006 Share Posted September 18, 2006 Or you could (if you like welding like me! ) just weld up a little cylinder shape or triangular box, fill it with Steel wool and "MAKE SURE" you put a drain on it to drain the oil. you can route all of your crankcase breathers everything through that then to the intake! my bro in law did that on his RS just a suggestion Link to comment Share on other sites More sharing options...
NorthWet Posted September 19, 2006 Share Posted September 19, 2006 Something to watch out for: IIRC, someone (calebz???) had drivability issues related to intake changes before the MAF, and seemed to be caused by flow disruption through the MAF. Hopefully, that intercooler will help avoid MAF/turbulent-flow issues. Link to comment Share on other sites More sharing options...
rallyruss Posted September 19, 2006 Share Posted September 19, 2006 this an interesting fix/mod. I fully understand the theory and aplication but have a few concernes. most turbos will pass some oil. so if you had the PCV system isolated you still will get some oil on the maf element over time. that of course leads to a lean condition. lean bad. possible motor damage. secondly the subaru maf Is a hot wire maf and uses the air charge temp to adjust mixture slightly. running after the turbo will cause it to assume its sucking down warm air all the time ( well big ol cone air filters do that too ) but its somthing to keep in mind as it will throw the system off slightly. I fit in the bypass valve camp. I have run multiple bypass setups with great sucess and no drawbacks. yeah the noise does not attract the attention of many bystanders but it is verry functional. and really.. I draw enough attention just by driving strange cars. no need to ask for more. Link to comment Share on other sites More sharing options...
ryostyle_the_¥akuza Posted September 19, 2006 Author Share Posted September 19, 2006 this an interesting fix/mod. I fully understand the theory and aplication but have a few concernes. most turbos will pass some oil. so if you had the PCV system isolated you still will get some oil on the maf element over time. that of course leads to a lean condition. lean bad. possible motor damage. secondly the subaru maf Is a hot wire maf and uses the air charge temp to adjust mixture slightly. running after the turbo will cause it to assume its sucking down warm air all the time ( well big ol cone air filters do that too ) but its somthing to keep in mind as it will throw the system off slightly. I fit in the bypass valve camp. I have run multiple bypass setups with great sucess and no drawbacks. yeah the noise does not attract the attention of many bystanders but it is verry functional. and really.. I draw enough attention just by driving strange cars. no need to ask for more. HAHAHA, said well. Start up enrichment under cold temperatures is off slightly, once warm not an issue. I'll be putting in a catch can this weekend and pulling the setup apart to inspect the mas. Link to comment Share on other sites More sharing options...
#89 Posted October 16, 2006 Share Posted October 16, 2006 RTY, Beautiful Job on the blow-through!!!! You may have already posted on these inquiries... if so, a kick in the right direction thread-wise would be fantastic... There is ALOT of info in the forums... I get disoriented sometimes! 1) What preps, if ANY, to the carb.... or just relying on the full seal of the box?? 2)Did you wind up using a Malpassi regulator or some such to adjust fuel pressure under boost? 3)What did you wind up doing for fuel return line? Hats off to you; Respectfully, #89 1989 Subaru JUSTY RS 4WD 122, 892 miles Link to comment Share on other sites More sharing options...
soobscript Posted October 16, 2006 Share Posted October 16, 2006 No carb. 4 injectors, computer controlled. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now