nipper Posted November 30, 2006 Share Posted November 30, 2006 I found this pic on my cell phone. Sorry its blurry, but what you see sticking out of the block is the endcap of the #2 piston connecting rod. http://www.ultimatesubaru.org/photos/showphoto.php?photo=13560&cat=935 nipper Link to comment Share on other sites More sharing options...
brus brother Posted November 30, 2006 Share Posted November 30, 2006 ... just a flesh wound:rolleyes: Link to comment Share on other sites More sharing options...
Virrdog Posted November 30, 2006 Share Posted November 30, 2006 I'm pretty sure that'll buff out. Link to comment Share on other sites More sharing options...
nedro Posted November 30, 2006 Share Posted November 30, 2006 My dad has an ultimate tool kit. Oh wait, I am dad. Link to comment Share on other sites More sharing options...
Distance Commuter Posted December 1, 2006 Share Posted December 1, 2006 JB Weld. Just kidding - sorry that happened to a car you know. Your daily driver?? Link to comment Share on other sites More sharing options...
jmickelct Posted December 1, 2006 Share Posted December 1, 2006 Would be interested to knowing the build up to said emergence... Have a 96 OBW with (increasingly likely) rod knock, now to the point that the engine is reluctant to even start... Any emerging knocking sounds? As per: http://media.putfile.com/Knocking-Subaru-Engine-22L (early stages... IMO) http://media.putfile.com/1996-Subaru-OBW-engine-knock http://www.ultimatesubaru.org/forum/showthread.php?t=58174&page=3&highlight=knock (final stages?!) Link to comment Share on other sites More sharing options...
nipper Posted December 1, 2006 Author Share Posted December 1, 2006 One morning in south dakota there was a rod knock. Then i drove from there to portland, seattle, all over un developed roads, and some times at triple digits. Coming out of San Fran, going up donner pass i stopped for gas. I was amazed how nice the car was running. i did smell a little more oil then usual, but thought that was the seperator plate. Continued going up the pass, 100 miles west of reno, the cruise control floored the car. That lasted about 2 seconds. The car downshifted, then there was lots and lots and lots of smoke. Poped the hood and oil all over. Car started, gushed oil, but got me off the road. Blu was dead Long live Blu (factory rebuilt hybrid block) nipper Link to comment Share on other sites More sharing options...
zyewdall Posted December 1, 2006 Share Posted December 1, 2006 I've seen one other subaru with almost the same look to it. It was an 1997 EJ22 -- rod went through the top of the front of the block. But from what I gather, it's pretty rare. And yes, it did still start and run somewhat, missing one piston, with the hole in the block. Z Link to comment Share on other sites More sharing options...
BruceyWV Posted December 1, 2006 Share Posted December 1, 2006 Identical to what happened to my 2000. Sept mine was a lot more violent. Link to comment Share on other sites More sharing options...
hankosolder2 Posted December 4, 2006 Share Posted December 4, 2006 Identical to what happened to my 2000. Sept mine was a lot more violent. Did you ever get yours back on the road? H6 swap or not? Just curious. Nathan Link to comment Share on other sites More sharing options...
subeman90 Posted December 4, 2006 Share Posted December 4, 2006 good question...curious too! Link to comment Share on other sites More sharing options...
BruceyWV Posted December 4, 2006 Share Posted December 4, 2006 Got the accessories, ECU, and harness, was going to buy the engine but it was going to be 3 weeks before i got it, + wiring job. Work requires I have a car. Didnt have much a choice once I started losing money. Just got an old one back in, when it goes I'll put the H6 in since I already have the parts, I'll probably order the engine soon, or spend the dough on a tiny lift. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now