mellow65 Posted December 16, 2006 Share Posted December 16, 2006 anyone know how much you have to shorten the drive line when you put a ea82 DR in a ea81 hatch? Link to comment Share on other sites More sharing options...
Phizinza Posted December 16, 2006 Share Posted December 16, 2006 Not sure. But just to let you know, the EA82 box is about 18cm shorter then the EA81 box. Link to comment Share on other sites More sharing options...
bratsrus1 Posted December 16, 2006 Share Posted December 16, 2006 Hey65 This is Jerry, if you are installing a 5 speed dual range tranny into a EA81 hatch back then you will have to get the drive line lenghten. It takes 48 inches of new tubing not counting the ends. Your stock drive line is to short, the 5 speed is shorter than the 4 speed. Thanks Jerry Link to comment Share on other sites More sharing options...
mellow65 Posted December 16, 2006 Author Share Posted December 16, 2006 Oh wow I thought it was shorting, well good to know. I guess a few calls to some drive line places to get some prices. so which part do you lengthen, the front part or the rear part. Hey65 This is Jerry, if you are installing a 5 speed dual range tranny into a EA81 hatch back then you will have to get the drive line lenghten. It takes 48 inches of new tubing not counting the ends. Your stock drive line is to short, the 5 speed is shorter than the 4 speed. Thanks Jerry Link to comment Share on other sites More sharing options...
GeneralDisorder Posted December 16, 2006 Share Posted December 16, 2006 EA81's have a single peice driveline, so you just lengthen the original. No need to use the two-peice. GD Link to comment Share on other sites More sharing options...
mellow65 Posted December 16, 2006 Author Share Posted December 16, 2006 oh thats good to know. is that because it has a shorter wheel base and the two-piece drive line isn't needed dude so if all goes well i may be moving all the stuff from the wagon to a hatch. I have to say it wouldn't be a hard decision to do, i have wanted one of the hatches as long as I can remember. we're talking me being a kid and seeing ads for them, that long ago. I'd take my 5speed DR, rear discs, and do the spfi swap on it. So i could be rocking a hatch soon, so cross your fingers. EA81's have a single peice driveline, so you just lengthen the original. No need to use the two-peice. GD Link to comment Share on other sites More sharing options...
GeneralDisorder Posted December 16, 2006 Share Posted December 16, 2006 EA81's never had two-peice drivelines. That was an EA82 thing. Your's already has the two peice because someone put in a 5 speed. As does my Brat. But no EA81 (hatch or otherwise) came with a 2 peice stock. The Hatch is the only EA series soob that has a different wheelbase. It's shorter making the stock single peice too short for a 5 speed, and the EA82 two-peice too long. I've never tried an EA81 (non hatch) single peice against a hatch with a 5 speed, but I suspect it will be just a tad too long or short. So that if you want a 5 with Hatch, it's custom driveline time. Good times on the Hatch. They are fun. GD Link to comment Share on other sites More sharing options...
mellow65 Posted December 16, 2006 Author Share Posted December 16, 2006 so then i wonder if you got a wagon drive line and maybe just had it shortened, hmmmm maybe, well we will see, when and if i ever make it to that point. I also figure shortening has to be cheaper then remaking. you wouldn't happen to have a wagon or brat drive line laying around i could test that idea with do you Link to comment Share on other sites More sharing options...
GeneralDisorder Posted December 16, 2006 Share Posted December 16, 2006 Yeah - I think I have some normal EA81 drivelines. But it's not going to be cheaper. They aren't going to reuse the tubing. They will use new tubing and balance it properly, etc. Seems the going rate is around $100 to $150. GD Link to comment Share on other sites More sharing options...
mellow65 Posted December 17, 2006 Author Share Posted December 17, 2006 Oh well never mind then. But I am now an owner of an 86 4x4 gl hatch. Sure it doesn't run but that's half the fun. Figure I'll strip the carb crap off and start with the spfi swap and go from there. well and if all is sh*t i have the motor from the wagon. Yeah - I think I have some normal EA81 drivelines. But it's not going to be cheaper. They aren't going to reuse the tubing. They will use new tubing and balance it properly, etc. Seems the going rate is around $100 to $150. GD Link to comment Share on other sites More sharing options...
mellow65 Posted December 17, 2006 Author Share Posted December 17, 2006 oh and i had to promise my girlfriend to stop buying more subarus till i got rid of some. what like 4 in my driveway is to many Link to comment Share on other sites More sharing options...
Phizinza Posted December 17, 2006 Share Posted December 17, 2006 what like 4 in my driveway is to many Only 4? lol.. I've got one, my brothers got one, my parents have one. Theres 3 wrecks down the driveway, and I'm still looking for more I can see where shes coming from though. Link to comment Share on other sites More sharing options...
heartless Posted December 17, 2006 Share Posted December 17, 2006 4 is nothing - we have 6! 3 drivers, 3 parts cars. and looking for more!!! decent ones are hard to come by in central Wisconsin. Link to comment Share on other sites More sharing options...
spigma01 Posted December 17, 2006 Share Posted December 17, 2006 I got my driveline made for about seventy bucks, but I also had already bought two new u-joints. It went into a 80 wagon w/5sp d/r. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now